Maintenance & Service; Caracteristiques Techniques - Skil 0502 Original Instructions Manual

• Suction accessory F 9
For projecting lines on smooth surfaces
- slide tool on accessory F
- place accessory F onto surface
- level the tool (ensure that the bubble in the relevant
level is centered)
- push 2 knobs
- use projected line as reference
• Clamp accessory G 0
For projecting lines on board materials (thickness 15 - 30
mm)
- slide tool on accessory G
- fasten accessory G onto board by turning knob
clockwise
- use projected line as reference
• Pin accessory H !
For projecting lines on plasterboard, soft wood, and other
soft materials
- slide tool on accessory H
- place accessory H onto surface
- level the tool (ensure that the bubble in the relevant
level is centered)
- push 2 knobs
- use projected line as reference
! be aware of the sharp pins
• Magnet accessory J @
For projecting lines on any ferrous metal surface or profile
- slide tool on accessory J
- place accessory J onto surface
- level the tool (ensure that the bubble in the relevant
level is centered)
- use projected line as reference
• Screw accessory K #
For projecting lines at the same level as already mounted
screw
- place accessory K over already mounted screw
- level the tool (ensure that the bubble in the relevant
level is centered)
- use projected line as reference for mounting other
screw(s)
Screw accessory K can also be used in combination with
tape or drawing-pins
• Graduated arc accessory L $
For projecting lines at any desired angle from 0° to 90°
- remove knob by turning it counter-clockwise
- slide tool on magnet accessory J
- fasten magnet accessory J on accessory L by turning
knob clockwise
- move tool over graduated arc by loosening/fastening
knob
Graduated arc accessory L can also be used in
combination with tape or drawing-pins
• Belt clip accessory M %
For easy and convenient storage
MAINTENANCE / SERVICE
• Do not expose the tool to continuous vibration or
extremely hot or cold temperatures
• Always store the tool indoors in its protective carton/case
• Always keep the tool free of dust, moisture and direct
sunlight
• Clean the tool with a damp cloth and mild soap
! always remove the batteries before cleaning the
lens
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skil.com)
ENVIRONMENT
• Do not dispose of electric tools, batteries,
accessories and packaging together with household
waste material (only for EU countries)
- in observance of European Directive 2012/19/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 4 will remind you of this when the need for
disposing occurs
Niveau laser toutes surfaces
INTRODUCTION
• Cet outil est conçu pour aligner des objets et/ou marquer
des lignes de coupe par projection d'un faisceau laser;
les accessoires fournis permettent de l'utiliser sur les
surfaces les plus diverses
• Prêtez attention aux consignes de sécurité et aux
avertissements; ne pas suivre ces instructions peut
entraîner des graves blessures
• Conservez ces instructions dans un lieu sûr et
remettez-les à tout nouvel utilisateur de l'appareil
de mesure

CARACTERISTIQUES TECHNIQUES

Type de laser
Classe laser
Alimentation
Température de fonctionnement
Température de stockage
Poids
Exactitude déviation de
ELEMENTS DE L'OUTIL 1
A Interrupteur marche/arrêt
B Niveau à bulle pour lignes horizontales
C Niveau à bulle pour lignes verticales
D Ouverture du rayon laser
E Couvercle du compartiment des piles
F Support à ventouses
G Support à griffe
8
0502
635 nm, <1 mW
2
3 piles AG13
-10°C à 40°C
-20°C à +60°C
0,05 kg
± 10 mm à une distance
de 5 mètres