Sealey SA2415 Instructions Manual

Model No's: SA2415 (24ltr/1.5HP) SA2420 (24ltr/2.0HP) SA5020 (50ltr/2.0HP) SA5025 (50ltr/2.5HP)
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
IMPorTAnT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
SA2415
1. SAFETY INSTRUCTIONS
1.1. ELECTRICAL SAFETY.
q
WARNING! It is the user's responsibility to read, understand and comply with the following:
You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads, plugs
and all electrical connections for wear or damage. You must ensure the risk of electric shock is minimised by the installation of appropriate
safety devices. An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend
that an RCD (Residual Current Device) is used with all electrical products. It is particularly important to use an RCD with portable products
that are plugged into an electrical supply not protected by an RCCB. If in doubt consult a professional electrician. You may obtain a
Residual Current Device by contacting your Sealey dealer. You must also read and understand the following instructions concerning
electrical safety.
1.1.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, at least once a year, using a Portable Appliance Tester (PAT).
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances,
and the safety of appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure the insulation on all cables and the product itself is safe before connecting to the mains power supply. See 1.1.1. & 1.1.2.
above and use a Portable Appliance Tester (PAT).
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply leads and plugs for wear or damage and connections to ensure
that none are loose.
1.1.6. IMPORTANT! Ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7. DO NOT pull or carry the powered appliance by its power supply lead.
1.1.8. DO NOT pull power plugs from sockets by the power cable.
1.1.9. DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a qualified electrician. When an ASTA/BS approved UK
3 pin plug is damaged, cut the cable just above the plug and dispose of the plug safely.
Fit a new plug according to the following instructions (UK only).
a) Connect the grEEn/YElloW earth wire to the earth terminal 'E'.
b) Connect the broWn live wire to the live terminal 'l'.
c) Connect the bluE neutral wire to the neutral terminal 'n'.
After wiring, check there are no bare wires, that all wires have been correctly connected, that the cable outer insulation
extends past the cable restraint and that the cable restraint is tight.
Double insulated products are often fitted with live (BROWN) and neutral (BLUE) wires only. Double insulated products are always
marked with this symbol
to the earth terminal.

IMPORTANT! The use of extension leads to connect this compressor to the mains is not recommended as the resulting voltage drop
reduces motor, and therefore pump performance.
1.2. GENERAL SAFETY INSTRUCTIONS
3
Familiarise yourself with the application and limitations of the compressor.
3
Ensure the compressor is in good order and condition before use. If in any doubt do not use the unit and contact an electrician/service agent.

WARNING! Compressor must only be serviced by an authorised agent. Do noT tamper with, or attempt to adjust, pressure
switch or safety valve.
3
Before moving, or maintaining the compressor ensure it is unplugged from the mains supply and that the air tank pressure has been vented.
3
Maintain the compressor in good condition and replace any damaged or worn parts. Use genuine parts only. Unauthorised parts may be
dangerous and will invalidate your warranty.
. To re-wire, connect the brown & blue wires as indicated above. Do noT connect the brown or blue wires
Original Language Version
INSTRUCTIONS FOR:
COMPRESSORS 24LTR
& 50LTR DIRECT DRIVE
SA2420
Yellow & green
Earth Wire
blue
neutral
Wire
RECOMMENDED
FUSE RATING: 13 AMP
SA2415, SA2420, SA5020, SA5025
brown
live
Wire
Cable
restraint
Issue: 5 - 21/05/12