Dell EMC DP4400 Installation Manual
Integrated data protection appliance
Hide thumbs
Also See for DP4400:
- Service procedures (88 pages) ,
- Getting started manual (52 pages) ,
- Hardware installation manual (17 pages)
Table of Contents
Advertisement
Installation Guide
Dell EMC Integrated Data Protection Appliance
DP4400
Version 2.3
302-005-528
REV. 04
September 2019
overview.................................................................................................. 2
rails............................................................................................................5
bezel..........................................................................................................9
iDRAC...................................................................................................... 12
resources................................................................................................. 17
system.................................................................... 3
Tool...................................................................................5
cabinet................................................................................... 7
cabinet................................................................................. 7
network......................................................................... 10
on...................................................................11
Manager.......................................................... 16
patch.........................................12
Advertisement
Table of Contents
Related Manuals for Dell EMC DP4400
Summary of Contents for Dell EMC DP4400
-
Page 1: Table Of Contents
Installation Guide Dell EMC Integrated Data Protection Appliance DP4400 Version 2.3 302-005-528 REV. 04 September 2019 Installation overview....................2 Prepare the site and unpack the system..............3 Install Network Validation Tool...................5 Install the rails......................5 Secure the rails to the cabinet................... 7 Install the system in the cabinet................. -
Page 2: Installation Overview
Installation Guide Installation overview This guide is designed for personnel who install, configure, and maintain the Integrated Data Protection Appliance DP4400. To use this hardware publication, you should be familiar with digital storage equipment and cabling. Before you begin Gather the required materials and configure your network environment as specified in... -
Page 3: Prepare The Site And Unpack The System
Table 1 on page 4. Note: The DP4400 installation requires IP addresses strictly from a single subnet having a single gateway. 2. Register the 13 IP addresses in DNS with forward and reverse lookup entries for each address. Ensure that the router for the 13 IP addresses can be pinged. - Page 4 Ensure that ICMP is enabled in your network environment. The deployment of the appliance fails if ICMP is disabled. 3. Download the license files for Data Domain Virtual Edition (DDVE), Avamar Virtual Edition (AVE), and Data Protection Advisor (DP Advisor) from the Dell EMC Software Licensing Central. Note: For DP4400, only during the initial activation, the license keys are automatically downloaded from the ELMS server if you are connected to a network.
-
Page 5: Install Network Validation Tool
The rails are labeled left and right, and cannot be interchanged. The front side of each rail is labeled Left Front or Right Front when the rail faces the cabinet front. Dell EMC Integrated Data Protection Appliance DP4400 2.3 Installation Guide... - Page 6 Figure 2 Installing the front end of the rail 6. Repeat the preceding steps to install the right rail assembly. Dell EMC Integrated Data Protection Appliance DP4400 2.3 Installation Guide...
-
Page 7: Secure The Rails To The Cabinet
Procedure 1. At front of the cabinet, pull the inner slide rails out of the cabinet until they lock into place. Dell EMC Integrated Data Protection Appliance DP4400 2.3 Installation Guide... - Page 8 The slam latches will engage to secure the system in the cabinet. Note: Ensure that the inner rail slides completely into the middle rail. The middle rail locks if the inner rail is not fully engaged. Dell EMC Integrated Data Protection Appliance DP4400 2.3 Installation Guide...
-
Page 9: Install The Bezel
1. Align and insert the right end of the bezel onto the system. 2. Press the release button and fit the left end of the bezel onto the system. 3. Lock the bezel by using the key. Dell EMC Integrated Data Protection Appliance DP4400 2.3 Installation Guide... -
Page 10: Connect The System To The Network
Figure 7 Installing the front bezel Connect the system to the network About this task The following figure shows the location of the DP4400 network ports and iDRAC port. Figure 8 DP4400 network and iDRAC connections Procedure 1. Use a Cat 5e or Cat 6 copper Ethernet cable to connect a 1 GbE port (10) to the service computer. -
Page 11: Connect The Power Cables And Power On
DP4400 ports About this task The following table provides the port type for the DP4400 ports. Table 3 DP4400 port types Callout number Port type iDRAC 10 GbE (required) 10 GbE (required) 10 GbE (unused) 10 GbE (unused) 10 GbE (unused) -
Page 12: Configure Idrac
N.N.N is the latest pre-installation patch version and nnnnnn is the build number. Where You can install the pre-installation patch when the DataProtection-ACM is not registered with Secure Remote Services gateway by using SSH. Dell EMC Integrated Data Protection Appliance DP4400 2.3 Installation Guide... - Page 13 In the Port number field, specify the default port number 22. d. In the User name field, enter root e. In the Password field, enter Idpa_1234 f. Click Login. The following figure shows a sample WinSCP session configuration window. Dell EMC Integrated Data Protection Appliance DP4400 2.3 Installation Guide...
- Page 14 3. Create a temporary folder /tmp/patch. 4. Copy the Idpa_pre_update_N.N.N.nnnnnn.tar.gz file to the /tmp/patch directory. 5. Connect to the DataProtection-ACM by using Putty from the service laptop. The following figure shows the Putty configuration screen. Dell EMC Integrated Data Protection Appliance DP4400 2.3 Installation Guide...
- Page 15 The contents are extracted to a subdirectory named Idpa_pre_update_N.N.N.nnnnnn. 11. Change directory to Idpa_pre_update_N.N.N.nnnnnn.tar.gz directory by typing the following command: cd /tmp/patch/Idpa_pre_update_N.N.N.nnnnnn/ 12. Change permission of install.sh file by typing the following command: chmod +x install.sh Dell EMC Integrated Data Protection Appliance DP4400 2.3 Installation Guide...
-
Page 16: Launch The Appliance Configuration Manager
IDPA software, and configure the IDPA. To continue configuring the IDPA with the ACM, refer to the Integrated Data Protection Appliance DP4400 Getting Started Guide . This document explains common user tasks such as how to create backup policies and restore from backup. -
Page 17: Additional Resources
Information about software components and versions that are used in the IDPA product. IDPA training resources Video walkthroughs, demonstrations, and explanations of product features are available online. You can obtain additional IDPA training and information at https://education.emc.com. Dell EMC Integrated Data Protection Appliance DP4400 2.3 Installation Guide... - Page 18 PARTICULAR PURPOSE. USE, COPYING, AND DISTRIBUTION OF ANY DELL SOFTWARE DESCRIBED IN THIS PUBLICATION REQUIRES AN APPLICABLE SOFTWARE LICENSE. Dell Technologies, Dell, EMC, Dell EMC and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be the property of their respective owners. Published in the USA.