Download Print this page

Briggs & Stratton P4500 Operator's Manual page 12

Hide thumbs Also See for P4500:

Advertisement

Operation
Generator Capacity
To make sure your generator can supply enough running
watts and starting watts for the items you will power at the
same time, follow these three simple steps:
1. Select the items you will power at the same time. See
following list for typical wattages.
Tool or Appliance
Light Bulb - 75 Watt
Refrigerator/Freezer
Window AC - 10,000 BTU
Microwave Oven - 1000 Watt
Plasma Television - 50"
Laptop
* Typical wattages listed are approximate only. Check tool
or appliance for actual wattage.
** The momentary electrical current the generator can
provide to start electric motors, per Briggs & Stratton
standard 628K. It does not represent the power required to
continuously run electrical loads. It is the maximum current
that can momentarily be supplied when starting a motor,
multiplied by the generator's rated voltage.
2. Total the running watts. This is the amount of power
your generator must produce to keep your items
running. See following example:
Example
Tool or Appliance
Window AC - 10000 BTU
Refrigerator/Freezer
Plasma Television
Light (75 Watts)
Total running watts
Highest starting watts
Total generator watts required
3. Estimate the starting watts you will need. Because not
all motors start at the same time, total starting wattage
can be estimated by adding only the item with the
highest additional starting watts requirements to the
total running watts from step 2.
Power Management
To manage generator power, sequentially add loads as
follows:
1. With nothing connected to generator, start the engine
outdoors.
2. Plug in and turn on the first load, preferably the largest
load you have.
12
Running
Starting
Watts*
Watts**
75
550
1350
1000
2100
1000
500
250
Running Watts
Starting Watts
1000
2100
550
1350
500
75
2125 Total
2100 Highest
Running Watts
Starting Watts
= 2125
= 2100
= 4225
3. Permit the generator output to stabilize (engine runs
smoothly and attached device operates properly).
4. Plug in and turn on the next load.
5. Again, permit the generator to stabilize.
6. Repeat steps 4 and 5 for each additional load.
Never add more loads than the generator capacity. Take
special care to consider starting watts in generator capacity.
Carbon Monoxide (CO) Shutdown System
-
Automatically shuts down the engine when harmful levels
of carbon monoxide accumulate around the generator or
a CO shutdown system fault occurs. After shutdown, the
indicator light will blink for at least five minutes per the
-
chart below.
-
The CO shutdown system DOES NOT replace carbon
-
monoxide alarms. Install battery-powered carbon monoxide
alarm(s) in your home. Do not run generator in enclosed
areas.
Color/Pattern
Red
• • ••
Blue
• • •
*Blue light will blink for five seconds at the startup of generator to
show the CO shutdown system is functioning properly.
Step 5: Generator Shutdown
1. Turn off and unplug all electrical loads from generator
panel receptacles. Never stop engine with electrical
devices plugged in and turned on.
2. Let engine run at no-load for one minute to stabilize
internal temperatures of engine and generator.
3. Press the on/off button on the generator or either
button on the remote start fob.
Description
Carbon monoxide accumulated around
generator. Move generator to an open,
outdoor area 6.1 m from occupied
spaces with exhaust pointed away.
Automatic shutoff is an indication
generator was improperly located. Air
out premises (e.g. open windows and
doors) before reoccupying.
If you start to feel sick, dizzy, weak, or
your homes carbon monoxide alarm
sounds while using this product, get to
fresh air right away. Call emergency
services. You may have carbon
monoxide poisoning.
CO shutdown system fault occured*.
See Briggs & Stratton authorized service
dealer.
BRIGGSandSTRATTON.com.au

Hide quick links:

Advertisement

loading

This manual is also suitable for:

030807
Save PDF