Table of Contents
Advertisement
© BOSTITCH 2019
FEEDING PROBLEMS
1. If rings do not feed smoothly down the magazine,
GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE
check pusher spring for proper tension. If the
compliance for the products.
magazine is covered with dirt from field use, clean
the magazine and apply a light coating of oil.
FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signifient en
2. When rings feed properly on the magazine but do not
rien que les produits soient conformes aux normes CE.
feed into the jaws without spitting out of the magazine
side of the tool, or if the rings sit in the jaw grooves on
DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen nicht
an angle, check jaws to insure freedom of movement.
With the jaws void of rings, the vertical movement
die CE-Richtlinien für Produkte.
should be approximately .06" (1.5 mm). The jaw bolt
nuts should be snug, but never over-tightened.
NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet
3. After considerable use or several jams, the fingers
zeggen dat de producten voldoen aan de CE-vereisten.
on the pusher may show signs of spreading. This may
cause the pusher to "hang up" on the magazine, with
DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for
little or no pressure behind the rings. The last few
produkterne.
rings in the strip will not feed into the jaw mechanism.
The pusher fingers can be squeezed back into proper
FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-
position or the pusher should be replaced. NEVER
USE LOOSE RINGS IN THE SC TOOL.
yhdenmukaisuutta.
GR Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα
αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.
IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la
conformità CE per i relativi prodotti.
TROUBLESHOOTING
NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for
CE-merking for produktet.
PROBLEM
PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em
conformidade com a CE para os produtos.
ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
Inside diameter of ring too large
SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
after clinching
conformidad con las normas CE de los productos.
PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu
nie stanowią deklaracji zgodności CE prezentowanych produktów.
CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu
nie stanowią deklaracji zgodności CE prezentowanych produktów.
Inside diameter of ring too small
after clinching
SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané
výrobky.
HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem
Ring points not entering opposite
jelenti a termék CE-megfelelőségét.
jaw
RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă
conformitatea CE pentru produse.
m WARNING SERVICING & TROUBLESHOOTING
Maintenance and adjustment of these tools should be
made only by authorised agents of BOSTITCH or by other
experts giving due regard to the safety, operating and
maintenance instructions in this manual and the Safety
Operating Instructions Manual.
CAUSES
Latch worn
Wrong latch used (too short)
Latch spring broken
Wrong jaws used
Worn jaws (helix, cam surface, bolt
holes, jaw bushings)
Worn rollers
Wrong rollers (too small)
Wrong jaws
Jaw stops worn or polished off
Tip of jaw broken off
Mismatched jaws (Jaws should be
replaced only in pairs)
Rings only curling in one jaw
REMEDIES
Replace latch
Verify and replace latch
Replace latch spring
Verify and replace jaws
Replace jaws
Replace rollers
Verify and replace rollers
Verify and replace jaws
Replace jaws
Replace jaws
Verify and replace jaws
Replace jaws
GB
Advertisement
Table of Contents
