Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for EL EL-2648
-
Page 2: Receiver Installation
1 Introduction The EL-2648 is a stand-alone receiver that enables Electronics Line 3000's range of supervised wireless transmitters to be used with most popular hardwire control panels. The stand-alone receiver provides an interface between wireless devices and the control panel's wired zone inputs. The EL-2648 includes a simple, menu-driven programming interface and supports up to 8 individual detectors and 16 keyfobs. - Page 3 STEP 4: Permanently install the stand-alone receiver and the transmitters STEP 1: Planning the installation When planning the installation, consider the following guidelines: • Whenever possible, mount the receiver centrally in relation to wireless transmitters. • Avoid installation in close proximity to sources of high noise or radio frequency interference. For example, metal air conditioner/heater ducts and circuit breaker boxes.
- Page 4 STEP 2: Registering transmitters For the receiver to recognize a transmitter, it must be registered. In general terms, transmitter registration means sending two transmissions from a device when the receiver is in Registration mode. To register transmitters to the receiver: 1.
-
Page 5: Terminal Block Connections
4. Thread all the required cables through the wiring hole from the rear of the cover and make all necessary wiring connections as described in the following section – do not apply power yet! 5. Mount the receiver to the wall using the four screws supplied with the kit. 6. - Page 6 2.3 Keyfob Functions The EL-2648 supports two types of keyfob transmitter, EL-2611 and EL-2614. You can register up to 16 keyfobs to the stand-alone receiver. Figure 7 illustrates these transmitters and the functions assigned to their buttons. Disarm Panic Panic -...
- Page 7 Figure 8: Menu Structure...
-
Page 8: General Configuration
• ARM/DIS – The output reacts to arm and disarm transmissions from 4-button keyfobs (EL-2614). There are two relay operation modes available for Arm/Disarm. To choose the Arm/Disarm mode, press SELECT and use the navigation keys to choose one of the following modes. - Page 9 The following options are available: • ZONE 2 – The output is used as a regular zone output. • PANIC – The output reacts to panic transmissions from 1-button keyfobs or SOS transmissions from 4-button keyfobs - see Figure 7: Keyfob Button Assignments. 4.
- Page 10 Note: If you intend to use keyfobs, make sure that you have correctly programmed the appropriate output in the Configuration section of the menu – see 3.1.1 Output Configuration. If detection devices are registered to zone 1 or 2 and you wish to register keyfobs to the receiver (or vice-versa), it is important to delete unused registered devices.
- Page 11 4. Scroll using navigation keys to view other transmitters. 5. Press together to exit List mode. The List mode will be terminated automatically 60 seconds after the last keystroke. 3.4 Testing Transmitters Electronics Line 3000 recommends that you check all transmitters after installation. It is also recommended for users to carry out a walk test once a week to ensure that all transmitters are functioning correctly.
-
Page 12: Software Version
This chapter deals with the receiver’s behavior in normal operation mode when the tamper switch is closed. 4.1 System Displays During normal operation, the EL-2648 displays events as they happen. These events are displayed until the condition is restored. The following table explains each event display and the events that cause them to appear:... -
Page 13: System Status Led
The receiver’s status is normal. A trouble condition has occurred – see Table 3: System Displays (items 3-11). FLASHING Table 4: LED Indication 5 Technical Specifications Model number EL-2648 Zone Outputs Operating 868.35, 433.92, 418 or Trouble Outputs Frequencies 315MHz FM... - Page 14 ELECTRONICS LINE 3000 Ltd. - LIMITED WARRANTY ELECTRONICS LINE 3000 Ltd. (hereafter “EL3K”) warrants its products to be free from manufacturing defects in materials and workmanship for (Wireless – 12 months excluding batteries, Control Panels – 2 years, Dual Technology Detectors – 2 Years, PIR Detectors - 5 years) following the date of sale. EL3K will, within said period, at its option and in accordance with the terms of this Limited Warranty, repair or replace any product failing to operate correctly without charge to the original purchaser or user.
- Page 16 Contacting Electronics Line International Headquarters: All data is subject to change without prior notice. In no event shall Electronics Line 3000 Ltd. (EL3K) be liable for an amount in excess of Electronics Line 3000 Ltd. EL3K.’s original selling price of this product, for any loss or damage 14 Hachoma St., 75655 whether direct, indirect, incidental, consequential or otherwise arising out of Rishon Le Zion, Israel...