1. Manuals
  2. Brands
  3. Magnum Manuals
  4. Binding Machine
  5. MC-35A
  6. Product instruction manual

Magnum MC-35A Product Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Product instruction manual
Magnum MC-35A
The Magnum has been designed to be user friendly,
however we strongly recommend you take a few minutes
to read through this manual to ensure correct operation.
Keep this manual safe for future reference.

Advertisement

Table of Contents
loading

Related Manuals for Magnum MC-35A

Summary of Contents for Magnum MC-35A

  • Page 1 Product instruction manual Magnum MC-35A The Magnum has been designed to be user friendly, however we strongly recommend you take a few minutes to read through this manual to ensure correct operation. Keep this manual safe for future reference.

  • Page 2: Table Of Contents

    MC-35A Index INTRODUCTION ..................... 1 Preface ....................1 Specification ..................2 2 SAFETY ......................3 Environment ..................3 Do’s and Don’ts ..................3 2.3 Operating Instructions ................. 4 3 MAIN PARTS AND ACESSORIES ..............6 4 INSTALLATION ....................8 Uninstall the protection bar ..............8 Set the balance bracket ................

  • Page 3: Introduction

    MC-35A 1 INTRODUCTION 1.1 Preface This manual only applies to MC-35A Auto Creaser machine. Before using the machine, please read the instruction manual carefully first. Please keep the manual properly so that consulting it at any time in the future.

  • Page 4: Specification

    MC-35A 1.2 Specification Paper thickness 60-400 gsm Paper length 150-650mm Paper width 140-330mm Speed (One crease on A4): 75pcs/min (high) Sniper Speed (One crease on A4): 50pcs/min (high) Min crease gap Min gap from leading edge to first crease +/-0.2mm...

  • Page 5: Safety

    MC-35A 2 SAFETY Before or while operating this machine, you should pay great attention to the safety features. 2.1 Environment Temperature：10°C to 35°C Humidity: 30% to 70% Altitude: Below elevation 1000m There is no corrosiveness gas, flammable gas, oil mist and so on in room...

  • Page 6: Operating Instructions

    2.3 Operating Instructions English Please read these operation instructions before putting the machine into operation and observe the safety precautions. Model: MC-35A Input: 110V/220V 1. Children must not operate the machine! 2. Do not reach into the machine! 3. Long hair can become entangled in cutting head! 4.
  • Page 7 MC-35A 10. Top fold plate must lock into position correctly. 11. Remove the plug before cleaning the machine! Do not perform any repairs on the paper folding machine! 12．the socket-outlet shall be installed near the equipment and shall be easily accessible.

  • Page 8: Main Parts And Acessories

    MC-35A 3 MAIN PARTS AND ACCESSORIES 18 1716 15 14 Parts Description Locks the tool in position Slide-in bar lock Slide-in bar Could be crease bar or perforate bar To assist user slid in/out the tool Screw Optional Stand Option with caster...
  • Page 9 MC-35A Infinity adjust to control air flow Air gate sheet feed with double sheet detector Front guide Skew adjust wheel To change the angle of fixed side guide Press wheel To press the paper tail Stack height sensor To trigger the feeding job after loading table rise...

  • Page 10: Installation

    MC-35A 4 INSTALLATION 4.1 Uninstall the protection bar Protection The first thing after unpacking and putting machine on table is to uninstall the protection bar. 4.2 Set the balance bracket Balance bracket Please be careful of the bracket from your hand when you are moving it to the stand.

  • Page 11: Feeding Extension

    MC-35A 4.4 Feeding extension We can see there are 2 screws on rear of feeding table, and there are 2 holes on side of extension table. 4.5 Power socket and switch Switch (Press “O” is off, press “|” is On)

  • Page 12: Quick Start

    MC-35A 5 QUICK START Paper must be flat and not curled ,not hooked, cut straight and square Turn on machine, To lower tray feed, press STOP Put paper in the tray，against the fixed guide, front and side. Fit tray and outfeed tray extensions as required if over A3 , Pile must be even and square.

  • Page 13: Operation

    MC-35A 6 OPERATION 6.1 Control panel The control panel consist of keys and screen, as per following picture. 12 13 No Key Description STOP Stop the machine. START Run the machine. Machine will run one test sheet TEST CLEAR Clear the data or clear the error display...

  • Page 14: Operation Screen

    MC-35A 6.2 Operation Screen 6.2.1 Welcome Screen Turn on the machine, Welcome Screen will appear firstly as follow. It will last for 2 sec, then jump to Ready Screen automatically 6.2.2 Ready Screen When Ready Screen comes on it means machine has finished self- checking process.
  • Page 15 MC-35A Scan all information of the Ready Screen by pressing Page Down Key . The information is divided into 4 kinds except the main ready screen: Crease data, total sheets, crease qty., software version & serial number. Display rest crease data in 32.
  • Page 16 MC-35A 6.2.3 input Crease Data Screen Initially in this Mode, cursor flashes in Line 1), (which means data can be input), input the data , from 0-650.0,accurate to one decimal place. Press ENTER, cursor turns from 1) to the next line, namely line 2) and flashes in line 2).Input a data, press ENTER.
  • Page 17 MC-35A 6.2.6 cover Hinge Screen This is a mode specially for book covers make. Following are 2 pages of this mode, in which you can input 2 parameters. SPINE and THK, Spine means the first spine line to the leading edge, THK means the thickness of the book, namely the spine width.
  • Page 18 MC-35A 6.2.7 progressive Screen Input 1 and Enter, it means turning off progressive function and goes back to Ready Screen: Input 2 and Enter, it means active progressive function. Screen will jump as following to setting for the progressive crease: Progressive Type Inc: Increase Type;...
  • Page 19 MC-35A Feeding Direction If all the sheets creased on same position, the bounded book cannot be turned over lay flat like this drawing. With 3 kinds of crease mode, even thick paper can be turned over very easily and lay flat after binding.
  • Page 20 MC-35A In this way the book can be folded with a square back after saddle stitched Affection of above 4 parameters are as above drawings 6.2.8 feed Mode Screen User can choose Auto feeding mode or Manual feeding mode, Press 1 to choose Auto or 2 to choose Manual, the chosen has a * symbol beside, Press , it is selected.
  • Page 21 MC-35A c. Press Enter, Success comes out. It means job is recalled successfully. d. Screen jumps to Ready Screen, and the data become 10, 20, 30,40, 50, 60. e. If Press Enter, Failure comes out. It means the job No. doesn't exist inside.
  • Page 22 MC-35A a job, say, 10, 20, 30,40, 50, 60. Then it will go back to Ready Screen. b. Press Mode Key 8 times, We go to Save Job Screen. c. Input a number between 1-30,such as 10. d. Press Enter, Success comes out.
  • Page 23 MC-35A 6.2.12 Recalibrate Screen If the Crease line gap is stretched or shrinked, the crease tolerance will be accumulated as crease line increased. For a quick calibrate, we operate on Recalibrate Screen. Press Mode Key 8 times entering Recalibrate Screen. And Length flashes.

  • Page 24: Sniper Patent Technology

    MC-35A 6.3 Sniper Patent Technology Using the sniper mode there is no need to input crease data one by one to create a job. Print a mark on the position where you want to crease. Machine will crease on the mark on the fly.
  • Page 25 MC-35A 6.3.2 How to Use Sniper? 6.3.2.1 Read Mark and Crease Finished In One Cycle. Use this function，all sheets have to be printed with register mark. 1. Put a pile sheets on loading table. The side with register mark must in non-operation side. 2. Activate Sniper as per 6.3.1.

  • Page 26: Hardware Settings

    MC-35A positioning on the template. 2. When creasing in the middle of register mark, accuracy is ±0.3mm. 3. Distance from the leading edge(D1) is over 10mm. Distance to the tail(D2) is over 50mm. 4. ⑴ When the distance between two mark(D) is over 5mm, the function 6.3.2.2...
  • Page 27 MC-35A beside to make the crease line deeper or lighter The 3 screws in the middle are not to be adjusted 6.3.2 Front Guide Adjustment Front guide knob Sheets Front guides Turn the knob clockwise to make the gap small, and vice versa. Make it small when there are double feeding, make it large when paper can not pass.
  • Page 28 MC-35A Sensor knob Sensor trigger In Auto feed Mode,Turn the knob clockwise, the loadting table will rise higher ,vise versa. In Manual Mode, the knob should be turned to be max clockwise, or there will be error report E-2 (Elevator moter error) 6.3.5 Skew Adjustment...

  • Page 29: 7Optional Parts

    MC-35A 7 OPTIONAL PARTS 7.1 Slid-in Tools Cross Perforate bar Cross Crease bar There are 2 kinds of cross bar, Crease tool and Perforate tool. To make the sliding easy, we install the screw on the bar. To insert the tool, please do as per following.

  • Page 30: Linear Blade

    MC-35A 7.2 Linear blade 7.2.1 Introduction There are 4 kinds of linear optional blades, Scorer, Perforator, Kiss cutter and Slitter. Each tool consist of blade and anvil. 7.2.2 Installation Install the Blades on the tools mounter as follow. Screw 1 Screw 2 Screw 1 to fix the blade with the machine.
  • Page 31 MC-35A Clip 2. Grab the shaft, pull rightward to loosen it and remove it from the machine. 3. Remove the clip from the other side, loosen the set screw of anvils and install the new anvils in order. Mind the flat part of the shaft, all set screw should touch this flat surface.
  • Page 32 IMPORTANT INFORMATION Your MC-35A should reach you in perfect condition and is guaranteed for 1 Year from date of purchase covering defective parts and general wear and tear, this does not cover film jams, misfeeds or other operator related errors, which would be chargeable.

Table of Contents