Replacing The Power Cable - EINHELL GC-EM 1536 Original Operating Instructions

Electric lawn mower
Hide thumbs Also See for GC-EM 1536:
Table of Contents

Advertisement

Available languages

Available languages

between the user and the mower housing. Be
especially careful when mowing and changing
direction on slopes and inclines. Maintain a solid
footing and wear sturdy, non-slip footwear and
long trousers.
Always mow along the incline (not up and down).
For safety reasons, the lawn mower may not be
used to mow inclines whose gradient exceeds 15
degrees.
Use special caution when backing up and pulling
the lawn mower. Tripping hazard!
Tips for proper mowing
It is recommended that you overlap the mowing
swaths.
Only use a sharp blade that is in good condition.
This will prevent the grass blades from fraying
and the lawn from turning yellow.
Try to mow in straight lines for a nice, clean look.
The swaths should overlap each other by a few
centimeters in order to avoid stripes.
How frequently you should mow your lawn is
determined primarily by the speed at which
the grass grows. In the main growing season
(December - January) you will probably need to
mow the lawn twice a week, otherwise just once
a week. The cutting height should be between
4 - 6cm and the amount of growth before mowing
again should be 4 - 5cm. If the grass is allowed
to grow somewhat longer for whatever reason,
do not make the mistake of cutting it back to the
normal height in one go. This will harm the lawn.
Never cut it back by more than half the height in
one go.
Keep the underside of the mower housing clean
and remove grass build-up. Deposits not only
make it more diffi cult to start the mower; they
decrease the quality of the cut and make it harder
for the equipment to bag the grass.
Always mow along inclines (not up and down).
You can prevent the lawn mower from slipping
down by holding a position at an angle upwards.
Select the cutting height according to the length
of the grass. Make several passes so that no
more than 4cm of grass are cut at one time.
Switch off the motor before doing any checks on
the blade. Keep in mind that the blade continues
to rotate for a few seconds after the motor has
been switched off . Never attempt to manually
Anl_SA_GC_EM_1536.indb 26
Anl_SA_GC_EM_1536.indb 26
GB
stop the blade. Regularly check to see if the
blade is securely attached, is in good condition
and is sharp. If the contrary is the case, sharpen
the blade or replace it. In the event that the blade
strikes an object, immediately switch off the lawn
mower and wait for the blade to come to a com-
plete stop. Then inspect the condition of the blade
and the blade mount. Replace any parts that are
damaged.
Lay the power cable on the ground in loops in
front of the power outlet. Mow away from the po-
wer outlet and cable, making sure that the power
cable always trails in the mowed grass so that the
lawn mower does not travel over the cable.
As soon as grass clippings start to trail the lawn
mower, it is time to empty the grass basket. Im-
portant! Before taking off the grass basket, switch
off the motor and wait until the blade has come to
a stop.
To take off the grass basket, use one hand to lift
up the chute fl ap and the other to grab onto the
basket handle. Remove the basket. For safety
reasons, the chute fl ap automatically falls down
after removing the grass basket and closes off the
rear chute opening. If any grass remains in the
opening, it will be easier to restart the engine if
you pull the mower back approximately 1m.
Do not use your hands or feet to remove clippings
in or on the mower housing, but instead use suita-
ble tools such as a brush or a hand broom.
In order to ensure that the majority of grass clip-
pings are picked up, the inside of both the grass
basket and especially the net must be cleaned
after each use.
Reattach the grass basket only when the motor is
switched off and the blade has stopped.
Lift up the chute fl ap with one hand and, holding
the grass basket by its handle with the other
hand, hang in the basket from the top.

7. Replacing the power cable

Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
- 26 -
05.07.2018 08:37:28
05.07.2018 08:37:28

Advertisement

Chapters

Table of Contents
loading

Table of Contents