Table of Contents
Advertisement
Never place any object in the air intake open-
D
ing as this could restrict proper air flow and
cause damage to the unit.
Never use for spreading chemicals, fertiliz-
D
ers, or other substances which may contain
toxic materials.
To avoid spreading fire, do not use near leaf
D
or brush fires, fireplaces, barbecue pits,
ashtrays, etc.
Use only for jobs explained in this manual.
D
MAINTAIN YOUR UNIT PROPERLY
Have all maintenance other than the recom-
D
mended procedures described in the instruc-
tion manual performed by an authorized ser-
vice dealer.
Disconnect spark plug before performing
D
maintenance except for carburetor adjust-
ments.
Use only recommended Weed EaterŽ re-
D
placement parts; use of any other parts may
void your warranty and cause damage to your
unit.
Empty fuel tank before storing the unit. Use
D
up fuel left in carburetor by starting engine and
letting it run until it stops.
Do not use any accessory or attachment
D
other than those recommended by manufac-
turer for use with your unit.
Do not store the unit or fuel in a closed area
D
where fuel vapors can reach sparks or an
open flame from hot water heaters, electric
motors or switches, furnaces, etc.
Store in a dry area out of reach of children.
D
SPECIAL NOTICE:
For users on U.S. For-
est Land and in some states, including Cali-
fornia(Public Resources Codes 4442 and
4443), Idaho, Maine, Minnesota, New Jersey,
Oregon, and Washington: Certain internal
combustion engines operated on forest,
brush, and/or grass covered land in the above
areas are required to be equipped with a
spark arrestor, maintained in effective work-
ing order, or the engine must be constructed,
equipped, and maintained for the prevention
of fire. Check with your state or local authori-
ties for regulations pertaining to these re-
quirements. Failure to follow these require-
ments is a violation of the law. This unit is not
factory equipped with a spark arrestor; how-
ever, a spark arrestor is available as an op-
tional part. If a spark arrestor is required in
your area, contact your authorized service
dealer for the correct kit. The spark arrestor,
blower tubes, and nozzles must be as-
sembled to unit to be in full compliance with
regulations.
SPECIAL NOTICE:
Exposure to vibra-
tions through prolonged use of gasoline pow-
ered hand tools could cause blood vessel or
nerve damage in the fingers, hands, and
joints of people prone to circulation disorders
or abnormal swelling. Prolonged use in cold
weather has been linked to blood vessel dam-
age in otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek
medical attention. An antivibration system
does not guarantee the avoidance of these
problems. Users who operate power tools on
a continual and regular basis must monitor
closely their physical condition and the condi-
tion of this tool.
ASSEMBLY
WARNING:
Stop engine and be sure
the impeller blades have stopped turning be-
fore opening the vacuum inlet door or at-
tempting to insert or remove the vacuum or
blower tubes. The rotating blades can cause
serious injury. Always disconnect the spark
plug before performing maintenance or ac-
cessing movable parts.
WARNING:
If you receive your unit
assembled, check each step to insure your
unit is properly assembled and all fasteners
are secure.
A standard screwdriver is required for as-
D
sembly.
BLOWER TUBE ASSEMBLY
Align the rib on the blower tube with the
D
groove in the blower outlet; slide the tube
into place.
NOTE:
Tube clamp must be loose enough to
allow blower tube to be inserted in blower out-
let. Loosen tube clamp by turning knob coun-
terclockwise.
Blower
Outlet
Groove
Tighten the tube clamp by turning the knob
D
clockwise.
To remove the tube, turn the knob counter-
D
clockwise to loosen clamp; remove tube.
VACUUM BAG ASSEMBLY
Open the zipper on the vacuum bag and in-
D
sert the elbow tube.
Push the small end of the elbow tube
D
through the small opening in the bag.
Elbow
Tube
Zipper
Opening
NOTE:
Make sure edge of the small opening
is flush against the flared area of the elbow
tube, and the rib on the elbow tube is on the
bottom.
Close the zipper on the bag. Make sure the
D
zipper is closed completely.
Remove blower tube from engine.
D
-- 3 --
Blower
Tube
Rib
Small
Opening
Rib
Advertisement
Table of Contents
