TPL VISION BLBAR+ User Manual

Backlight, overdrive

Advertisement

Quick Links

Preamble
This Technical User Guide contains warnings and guidance for correct and safe operation of the product.
These instructions must be followed at all times. TPL Vision will not be held responsible for problems caused
by using the product contrary to these instructions and the Warranty will be deemed invalid.
UnPackIng
Products are packed in our factory, using suitable materials for a safe transport through the usual means of trans-
portation, in France and internationally. However, a damaged package must be reported to the carrier on delivery.
Hand-written reservations must be indicated on the delivery order. Moreover, please send a letter or an email to
TPL Vision as soon as possible (up to 24 hours after the delivery). If the transportation damage has not been stipu-
lated on the delivery order and reported to TPL Vision in time, the package will not be taken back nor exchanged.
To open the package, do not use any cutting blade to avoid damaging the product(s). Please use the delivered
accessories, if needed (do not use any other products or equivalents to replace the delivered accessories).
rISk claSS
The EN-62471 norm about lighting fluxes enables the classification of led lightings in 4 distinct groups, according
to their hazardousness degree. Please find below an indicative table, recapitulating the classes of risk for our
standard products.
Colour
White WHI, Green 525 nm, Red 630 nm
UV 405 nm, Blue 470 nm, IR 850 nm
UV 365 nm
UV 385 nm
TPL Vision can provide guidance notes about the nominal distance to minimize eye risks.
BewaRe to the infrared light, invisible to the eyes.
To know if the light is on, please refer to the LED indicators.
USer gUIde
Class
Risk
0
none
1
low
2
moderate
3
high
In all cases, TPL Vision recommends
the use of the protection glasses
that are listed in its catalog.
For more information about photo-
biological risks, do not hesitate to
contact us.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BLBAR+ and is the answer not in the manual?

Questions and answers

Summary of Contents for TPL VISION BLBAR+

  • Page 1 Hand-written reservations must be indicated on the delivery order. Moreover, please send a letter or an email to TPL Vision as soon as possible (up to 24 hours after the delivery). If the transportation damage has not been stipu- lated on the delivery order and reported to TPL Vision in time, the package will not be taken back nor exchanged.
  • Page 2: Led Indicators

    USer gUIde P2/8 dImenSIonS Length Height Width (mm) (mm) (mm) BLBAR + 125 47.6 BLBAR + 250 47.6 BLBAR + 375 47.6 BLBAR + 500 47.6 BLBAR + 625 47.6 BLBAR + 750 47.6 BLBAR + 875 47.6 BLBAR + 1000 1033 47.6 BLBAR + 1125...
  • Page 3: Daisy Chain

    P3/8 WIrIng 4 Male PointS 5 Male t Coding PointS 5 FeMale PointS Front view top view daISy chaIn LIGHT N°1 5 male 4 male LIGHT N°2 points points T coding 5 female LIGHT N°1 points Drive Linking cable LIGHT N°2 4 male 5 male points...
  • Page 4 USer gUIde P4/8 connectIon M12 Connector 5 male points - DRIVE PNP + dimming NPN + dimming grey DIM 0-10V black blue STROBE brown 24 VDC 24 VDC white STROBE 0-10V 0-10V Light will be in continuous mode by leaving signal on strobe input active. The M12 male connector 5 points is CoMPliant with the M12 female connector 4 points.
  • Page 5 P5/8 control The product is optimised for a lifespan >50kh in a 40°C atmosphere. In strobe mode, the strobing time is directly equivalent to the time during which the strobe entry is activated. Strobe PnP & nPn PnP : from 5 to 24V for 100% ON. From 0 to 1V for 100% OFF. nPn : less than 1V for 100% ON.
  • Page 6: Power Supply

    No thermal shock (max temperature variation: 10°C in 24h). eqUIPment maIntenance Cleaning (when the product is switched off) Please use a soft and dry cloth. Do not use any abrasive material. Do not use any cleaning solvent or aggressive chemical product. TPL Vision recommends to use isopropyl alcohol.
  • Page 7: User Security

    P7/8 USer SecUrIty Please respect the power supply voltages and the connection terminals. do not modify or dismantle all or part of the product. do not connect or clean when power is on. do not watch the lighting source directly, and follow the advice below : • If the workstation enables it, interpose a filter that will stop the lighting radiation under fixed or adjustable frame between the source and the operator.
  • Page 8 ViSion uK Brenchley House – School Road – Charing – Kent TN27 0JW – UK Tel. + 44 (0)1738 310 392 – www.tpl-vision.com...

Table of Contents