Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Eriez HD-46
Summary of Contents for Eriez HD-46
- Page 1 VM-3157G Installation, Operation and Maintenance Instructions VIBRATORY FEEDERS MODELS - HD-46, HD-56, & HD-66 ERIEZ MAGNETICS HEADQUARTERS: 2200 ASBURY ROAD, ERIE, PA 16506–1402 U.S.A. WORLD AUTHORITY IN SEPARATION TECHNOLOGIES Vibratory Feeder: Models HD-46, HD-56, & HD-66...
- Page 2 Introduction This manual details the proper steps for installing, operating and maintaining the Eriez Vibratory Feeder. Careful attention to these requirements will assure the most efficient and dependable performance of this equipment. If there are any questions or comments about the manual, please call Eriez at 814/835-6000 for Vibratory Feeder assistance.
-
Page 3: Table Of Contents
Table of Contents ERIEZ VIBRATORY FEEDER - MODELS HD-46, HD-56 & HD-66 INSTALLATION ..................... 4 Mounting ......................4 Electrical Connections ..................4 OPERATION AND MAINTENANCE ..............4 Tuning Guide ....................4 Tuning for Non-standard Trays ................ 5 Tuning for Different Conditions of Tray Loading ..........6 REPAIRS ....................... -
Page 4: Installation
AC source through a special and the mounting surface to prevent restriction of Eriez 30Hz control (see IOM - 414). It cannot be movement of the vibratory elements. operated from a DC source. -
Page 5: Tuning For Non-Standard Trays
HD units are normally set at approximately 3/16" The total stiffness of the tuning spring stack is the (4.7 mm) tray stroke. This can be checked with an Eriez sum of the relative stiffness numbers. By various deflection sticker. -
Page 6: Tuning For Different Conditions Of Tray Loading
In no case, however, nearby steel or iron objects. should the unit be permitted to deflect more than 3/16" (4.7 mm) without load for HD-46, HD-56 and HD-66. • Keep credit cards, computer disks and other magnetic storage devices away from... - Page 7 E-frame into the body cavity, making sure that the gaps. Tighten the electrical assembly plate and center leg enters the space between the armature replace the nameplates. pole pieces. Insert the bolts securing the electrical assembly and fasten only finger tight. Vibratory Feeder: Models HD-46, HD-56, & HD-66...
-
Page 8: Spring Replacement
Repairs Lay the unit on its side, making sure that the gap (cont.) spacers stay in place, and use a small hammer and flattened round bar or dowel to tap the SPRING CHANGE OR REPLACEMENT elastomer spring out of the body housing. Next, Refer to the Parts List Drawing and Figs. -
Page 9: Armature Replacement
Loosen slightly but do not remove the upper end of the front tuning spring stacks to the spring bar FIGURE 11 and the spring bar to the armature. Vibratory Feeder: Models HD-46, HD-56, & HD-66... - Page 10 The new Hi-Vi method incorporates a lifetime POTENTIOMETER permanent rare earth magnet and is operated directly POWER from an alternating current line through Eriez 30/40 Hz ELECTRO-MAGNET SUPPLY control. In the Hi-Vi method, the spring-mounted mass is alternately both attracted and repelled by an AC electromagnet assisted by the springs.
-
Page 11: Troubleshooting
Order new parts from factory and replace per instructions. Coil Failure Foreign Material Replace coil or coil and E-frame assembly. Order from Eriez parts lists. Follow maintenance Examine and remove foreign material. instructions carefully. Vibratory Feeder: Models HD-46, HD-56, & HD-66... - Page 12 19. Product Variation If product density, moisture content or other characteristics vary, customer should take own corrective measures. Eriez and Eriez Magnetics are registered trademarks of Eriez Manufacturing Co, Erie, PA ©2019 Eriez Magnetics All Rights Reserved World Authority in Separation Technologies ...
Need help?
Do you have a question about the HD-46 and is the answer not in the manual?
Questions and answers