Watts 7 Series Installation, Maintenance & Repair

Installation, Maintenance, & Repair
Series 7 Dual Check Valves
LF7/7, LF7R, LF07S/07S, LF7C/7C, 7B, LFL7/L7, and LFCu7/Cu7
" – 2" (15 – 50mm)
Sizes: ⁄
1
2
!
WAR NI NG
You are required to thoroughly read all installation instructions and product
safety information before beginning the installation of this product. FAILURE
TO COMPLY WITH PROPER INSTALLATION AND MAINTENANCE IN-
STRUCTIONS COULD RESULT IN PRODUCT FAILURE WHICH CAN
CAUSE PROPERTY DAMAGE, PERSONAL INJURY AND/OR DEATH.
Watts is not responsible for damages resulting from improper installation
and/or maintenance.
Local building or plumbing codes may require modifications to the informa-
tion provided. You are required to consult the local building and plumbing
codes prior to installation. If this information is not consistent with local
building or plumbing codes, the local codes should be followed.
Need for Periodic Inspection/Maintenance: This product must be test-
ed periodically in compliance with local codes, but at least once per year
or more as service conditions warrant. Corrosive water conditions, and/or
unauthorized adjustments or repair could render the product ineffective for
the service intended. Regular checking and cleaning of the product's inter-
nal components helps assure maximum life and proper product function.
Basic Installation Instructions
A. Watts dual check valves may be installed in either a vertical or a horizon-
tal position. Series 7 & LF7 should be installed downstream of the water
meter and of the water pressure regulator. All outlets including sill cocks
must be downstream of the Series 7. Model 07S & LF07S should be
installed at the fire sprinkler service connection to the main line.
B. They should always be installed in an accessible location to facilitate
the removal for servicing and testing.
C. Pipe lines should be thoroughly flushed to remove foreign material
before installing the unit.
D. Protect from freezing
E. Ensure that valve is installed in proper flow direction. Refer to flow
direction arrow on valve nameplate or body.
F. When installing valve in pipe line, only use wrenching flats provided.
Do not apply wrench to body of valve. This will prevent distorting the
valve body and component parts.
G. These valves incorporate an O-ring union seal that requires minimum
tightening of union nut. Do not overtighten.
H. These valves contain plastic check modules and should never be
directly sweated into the line. Sweat fit adapters should be sweated
into the line prior to valve installation.
I. Avoid improper application and excessive pipe sealants such as tef-
lon tape and pipe dope.
®
Quick-Connect Installation
To Connect:
1 ⁄ in. (38.1mm)
1
2
⁄ in.Pipe (12.7mm)
1
2
1 ⁄ in. (44.45mm)
3
4
3 ⁄ in.Pipe (19.05mm)
4
1 ⁄ in. (47.63mm)
7
8
1 in.Pipe (25.4mm)
1. Mark pipe as shown.
This is pipe insertion depth.
2. Clean pipe end.
PEX tubing only
Pipe Stiffener
Tail Piece
3. If using PEX tubing, insert pipe stiff-
ener (provided) into end of pipe.
4. Push tubing into tailpiece up to mark.
5. Insert collet clip.
Water Pressure
Reducing Valve
Water Meter
Main
Supply
To Disconnect:
1. Remove collet clip.
2. Depress collet.
Watts product specifications in U.S. customary units and metric are approximate
and are provided for reference only. For precise measurements, please contact
Watts Technical Service. Watts reserves the right to change or modify product
design, construction, specifications, or materials without prior notice and without
incurring any obligation to make such changes and modifications on Watts prod-
ucts previously or subsequently sold.
!
WARNING
When a pressure reducing valve or dual check valve is installed in the
supple line, it creates a closed system which makes plumbing code
compliance imperative for system safety. Special attention must be
given by all concerned to assure pressure relief protection is provided
to protect water heater equipment. It is important to make certain an
approved ANSI Z21.22 temperature and pressure relief valve is installed
on the storage water heater. This device is designed for emergency
safety relief and should not be used as an operating control.
High System Pressure
If the downstream system pressure is higher than the set pressure
under a no flow condition, the cause could be thermal expansion.
Thermal expansion occurs whenever is heated in a closed system.
You must make provisions for thermal expansion protection of your
plumbing system and components when installing a pressure reducing
valve or dual check valve in the supply line.
The use of pressure relief valves such as *Watts 530C, *BRV,
*Governor 80, *3L and or a potable water expansion tank such as the
Watts DETA and PLT may be required.
To determine if this is the result of thermal expansion, try briefly open-
ing the cold water tap. If the increased pressure is caused
by thermal expansion, the pressure will immediately be
relieved and the system will return to the set pressure.
Watts offers a pressure test gauge, model 276H300 to
assist you in determining if you have high water pressure.
The 276H300 when attached to a hose bibb registers the
highest pressure reading over the period of time it is
left on the system.
*NOTE:
The Watts 530C, BRV, Governor 80 and 3L
are not ASME approved safety relief valves. Under no
circumstances should these devices be used in place
of an ASME approved valve. Consult your local water
code authority to ensure installation compliance.
L7
to Fire sprinklers
07S
3. Pull tubing from tailpiece.
Watts 276H300
RP/IS-7
Water
Supply