Advertisement
2-3. Items requiring a support wire
Attach any wire to the handle section when a safety wire is required to the pan-tilt head. When attaching
the wires, be careful that nothing blocks operation of the pan-tilt head.
2-4. Waterproofing the receptacle unit
Inspect the waterproof connector for looseness. After
pass each cable through the waterproof tube and the
waterproof unit, insert the waterproof tube all the way
into the waterproof connector until its tip touches the end
and secure it in place. Put the end of the waterproof tube
in the safe place so that water, dust and moisture do not
enter. Also, do not seal the end of the waterproof tube
so as to mitigate the pressure rise inside of the product
caused by the temperature change. Connect each cable
to the receptacle unit of the main unit, and then secure
the waterproof unit to the pan-tilt head using the supplied
mounting bolts (x4).
Clamp the cables at appropriate intervals.
Step 3 Connections
Pan-tilt head pedestal unit
When connecting the MIC cable, be sure to always use the ferrite core
RFC-13 supplied with this product.
Ferrite core
Make one loop and
then attach.
Make one loop and attach the ferrite core to the cable within 10 cm from the
pan-tilt head connector.
Ferrite core RFC-13 for microphone
Receptacle unit (A-A section)
⑥Control output for arbitrary function
SD I
A UX
START
STOP
V B S
CONT
SYNC
①DC power
supply input
Connect power supplied from a
UL-approved AC adapter or the
⑤Control signal input for pan-tilt head,
secondary side safety circuit of
lens and camera*
a UL-approved power supply
circuit.
* Use the supplied RS-422 connector (PRC05-P12F/TAJIMI).
Power of two or three times the
rating 80 W may be consumed
during power-on, so select a
power supply with
specifications that prevent a
power failure.
GENERAL SAFETY INFORMATION
Failure to observe these warnings and cautions provided for the purpose of hazard prevention may result in injuries or
accidents. Read this installation manual carefully to familiarize yourself with its contents and to ensure proper installation of
this product. This installation manual uses the following symbols and terms in the warning and caution notices for preventing
accidents and protecting the safety of the customer and others.
Indicates a potentially hazardous situation which, if not heeded, may result in death or serious
WARNING
injury to you or others. Be sure to heed all warning notices to ensure safe operation at all times.
Indicates hazardous situations which, if not heeded, may result in minor or moderate injury to
CAUTION
you or other persons, or damages to your property.
Emphasizes essential inform which, if not heeded, may render the product unworkable or cause
NOTE
it to function improperly. Also, provides helpful information for operation.
WARNING
1. To prevent injury, this apparatus must be securely fixed in accordance with the installation manual.
2. This product shall not be exposed to excessive heat such as sunshine, fire or the like.
3. Do not install the unit in a location where there is a risk of combustion or ignition. When the unit is installed in a location
where inflammable gas collects or is produced, ignition may result which in turn may cause a fire.
CAUTION
1. When installing the unit, do not rotate the head and the camera forcibly by hand. It can cause damage to this device.
2. Do not install the unit in an unstable location such as on a wobbly table, on a sloping surface or in a location subject to
severe vibration. Doing so may cause the unit to fall down or topple over, possibly causing injury.
3. Do not install the unit in a location where it may be directly exposed to salt water (seawater) or where corrosive gas or
soot is present. Contact with such substances may corrode and degrade the mountings, ultimately causing the unit to
fall down and possibly causing injury.
4. When transporting the unit, hold the handle of the head unit and the bottom of the unit. Otherwise, the unit may be
dropped, possibly causing breakdown or injury.
5. When installing the unit in an elevated location, take appropriate measures to prevent the equipment and parts from
falling. Otherwise, the equipment and parts may fall, possibly causing injury.
6. Do not install the unit in a location where it may be directly exposed to sunlight for protecting the lens.
7. The unit does not have a freeze-proof structure, so it does not move when frozen. Take care when installing the unit in
a location where it may be frozen. This unit is not freeze-resistant and does not operate if frozen. Therefore, be careful
when installing in a location where it may freeze.
WARNING
1. Never attempt to connect or disconnect the power cord with wet hands. Doing so may cause electric shocks.
2. Connect the power cord securely to both the input connectors and the outlet.
If dust is allowed to accumulate on the exposed prongs of the power cord plug or if the prongs come into contact with
metal, fire or electric shocks may result. Disconnect the power cord periodically, and use a dry cloth to wipe off any
dust or dirt that has accumulated on the prongs and around the input connectors and the outlet. If the power cord is left
connected for extended periods of time in locations with high levels of dust, moisture or oily smoke, the accumulated
dust will absorb moisture, resulting in deterioration of the insulation and possibly fire.
3. Always remove the mounting screws before disconnecting the power cord. Placing excessive stress on the power cord
may break its wires or otherwise damage the power cord, and power may leak from the damaged area, resulting in fire
or electric shocks.
4. The power cord is not supplied. Using a cord that does not comply with the safety standard or is otherwise unsuitable
for the installation conditions (approved product, environment) may result in fire or electric shocks.
CAUTION
1. In order to ensure that the power plug can be unplugged at any time, never place objects around the power plug.
Otherwise, it may be impossible to disconnect the power plug in the event of an emergency.
2. Never connect or disconnect cables until making certain that the power is turned off. Doing so may cause electric
shock or damage.
HANDLING THE UNIT
WARNING
1. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
2. Do not allow the pan-tilt head or the inside of the housing to become wet, and do not allow water to enter inside or to
be spilled onto the head. Do not put any object which contains liquid such as a drink or a vase on this product. If water
has found its way inside the unit, stop using it immediately. Continuing to use the unit is a fire or electric shock hazard.
Pub No. B-IM-40113-5
Waterproof unit
mounting bolts (x4)
Fall prevention wire
(for waterproof unit)
Waterproof unit
Waterproof connector
Waterproof tube (L = 500 mm)
RohrFlex: RF-36 FLEXA
A
A
To the washer
To the MIC unit
⑥AUX pin assignment
(HR10A-10R-10S(71)/HIROSE）
1
FPU
②Digital video/
2
AUX1
audio output
3
AUX2
4
AUX3
5
AUX4
③SD composite
6
COM
signal output
7
8
9
10
⑤CONT pin assignment
④External sync signal input
(PRC05-R12M/TAJIMI)
Input/
Signal
Pin No.
output
name
A
Input
RX+
B
Output
TX+
D
Input
RX-
E
Output
TX-
J
GND
INSTALLATION
POWER SUPPLY
Step 4 Checks after Completion of Connection
Receptacle unit
Supply power to the pan-tilt head connector (receptacle).
Be sure to always perform waterproofing after supplying power. (Refer to "2-4. Waterproofing the recep-
tacle unit".)
Only for European Union and EEA (Norway, Iceland, and Liechtenstein)
This symbol indicates that this product is not to be disposed of with your household waste, according to the WEEE
Directive (2012/19/EU) and national legislation. This product should be handed over to a designated collection point,
e.g., on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for
recycling waste electrical and electronic equipment (EEE). Improper handling of this type of waste could have a
possible negative impact on the environment and human health due to potentially hazardous substances that are
generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute
to the effective usage of natural resources. For more information about where you can drop off your waste equipment
for recycling, please contact your local city office, waste authority, approved WEEE scheme or your household waste
disposal service.
For more information regarding return and recycling of WEEE products, please visit
www.canon-europe.com/weee.
This device complies with Part 15B of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15B of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
Do not make any changes or modifications to the equipment unless otherwise specified in the manual. If such changes or
modifications should be made, you could be required to stop operation of the equipment.
Ａ
Ｂ
Ｆ
Ｃ
Ｄ
Ｅ
Ｇ
Ｈ
Ｊ
Ｋ
Ｌ
Ｍ
3. Do not attempt to disassemble or remodel the unit. High-voltage parts and intermeshing gears are to be found inside
the unit, and contact with them may cause injury.
4. Do not drop the unit, bump into other objects or otherwise subject it to strong impact. If the main unit has been
damaged, disconnect the power cord from the input connectors. Then contact your dealer or your Canon
representative.
5. Please do not turn the lens toward the sun. When a strong light enters at the TELE side, it can cause damage to the
lens and the camera.
6. When operating this device, please use a control device such as an operation unit. When panning or tilting by hand or
other methods, it can cause damage to this device.
CAUTION
1. Make sure that all the mountings are tightened securely. A loose mounting may cause the unit to fall down, possibly
resulting in injury.
2. Periodically (every 6 months to a year as a general rule) inspect the mountings for looseness. A loose mounting may
cause the unit to fall down, possibly resulting in injury.
WARNING
1 . Clean only with dry cloth.
2. Before cleaning the outside paneling of the unit, always disconnect the power cord from the input connectors.
Furthermore, do not use benzene, paint thinners or other easily ignitable substances for cleaning purposes. Doing so
is a fire and electric shock hazard.
3. This system should not be opened or disassembled, except by qualified service personnel.
• Dangerous parts are to be found inside the unit, contact with them may cause finger pinch and electric shock
hazard.
• If foreign objects and dust enter the inside, it may cause damage to this device.
• In case of high temperature and high humidity, internal damage and condensation may occur if humid air is allowed
to enter this device.
WARNING
1. Before transporting the unit, return the housing to the horizontal position. When transporting the unit, place it inside the
original shipping carton which was used specifically to house the unit.
1. Canon shall bear no responsibility for damage resulting from improper operation of this product by the customer.
2. Canon makes no guarantees of suitability and marketability for the customer's purpose, concerning product quality,
functions or this installation manual. Moreover, Canon shall bear no responsibility for any damage, direct or incidental,
that results from usage for the customer's purpose.
3. Canon shall make no guarantees about the results obtained using this product.
4. The product specifications, configuration, and appearance are subject to change without prior notice.
5. For further information on repairs, maintenance, or adjustments not mentioned in this operation manual, contact your
Canon dealer or your Canon sales representative.
6. Note that Canon may be unable to undertake servicing or repair of a product if it is modified without consulting Canon
or your Canon sales representative.
We, Canon Inc., in Japan and CANON EUROPE LTD., in U.K., confirm that the Remote pan-tilt head BU-47H is in conformity
with the essential requirements of EC Directive(s) by applying the following standards
EN55032 and EN55103-2
Note:
a) Applicable Electromagnetic Environments:
E-1 (residential), E-2 (commercial and light industrial), E-3 (urban outdoors) and E4 (controlled EMC environment, ex.
TV studio).
b) Use of shielded cable is required to comply with limits specified by above standards.
c) Use of ferrite core is required to comply with limits specified by above standards.
Dieses Produkt ist zum Gebrauch im Wohnbereich, Geschäfts- und Gewerbebereich sowie in Kleinbetrieben vorgesehen.
CANON INC.
30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan
Canon Europe Ltd
3 The Square, Stockley Park, Uxbridge, Middlesex, UB11 1ET UK
© 2015.05 CANON INC.
LED
START switch
A UX
START
STOP
Back
side
CONT
FCC REGULATIONS
Canadian Radio Interface Regulations
CAN ICES-3(A)/NMB-3(A)
KCC-REM-CIN-BU-47H
MAINTENANCE AND INSPECTION
STORAGE
TO THE CUSTOMER
All rights reserved. No part of this operation manual
may be reproduced or copied in any from or by any
means without the written permission of Canon Inc.
SD I
V B S
SYNC
Receptacle unit
4/6
Advertisement
