Advertisement
Remote Control Pan-Tilt Head
BU-47H 1AM/BU-47H 2AM
INSTALLATION MANUAL(B-IM-40113-5)
Read "GENERAL SAFETY INFORMATION" (back side) before using the product.
The safety cautions must be observed.
Read this operation manual before using the product. Keep the manual in place for
future reference.
[External View]
Center of
PAN rotation
Center of
TILT rotation
Optical
axis
90
4ｘφ8.6
Mounting bolts
Contact us.
Please contact us if you have questions on the products.
Canada: Canon Canada, Inc. Broadcast and Communications Div.
Tel:+1(905)795-2012
Fax:+1(905)795-2087
Mexico: Canon Mexicana, S. de R.L. de C.V. Call Center Div.
Tel:+52 55 5249 4905
USA : Canon U.S.A., Inc. ITCG METC
Tel:+1(800) 423-5367 (Toll Free)
Fax:+1(201) 807-3344
Asia and Hong Kong, S.A.R. : Canon Hongkong Company Ltd. ICP Marketing Div.
Tel:+852-3191-2333
1-3. Handling of the unit
When carrying the unit, hold the unit by its handle. Be careful not to
rotate the housing and head forcibly.
1-4. Fixing of the unit
The dimensions for drilling the holes in the floor are shown below.
When the floor interferes with the cables, prepare φ 185 to 200 steel spacers to prevent interference. Use
steel bolts with a length that enables a screw-in depth of 12 mm or more into the floor, and fix the unit se-
curely to a strong floor surface. Use a level to check that the floor and the head unit are horizontal.
4 x φ8.6
mounting bolts M8
90
L=25+t
+12 or more
2
1-5. Attaching the washer and microphone (option)
To also install a washer or microphone, please obtain the mounting jigs (not included).
For more information about optional products, please contact your Canon dealer or your Canon sales repre-
sentative.
Pub No. B-IM-40113-5
A-A section (Receptacle unit)
188
150
110
58
74.5
134.6
244
M8×1.25 L=35
Handle
Spacer (steel)
(if necessary)
φ185 ~ 200
t
= 12 mm or more
1
Step１ Installation
1-1. System connections
Short distance transmission
Operation unit
(MIC audio embedded)
GEN LOCK
SD
I
A U
X
V B S
C
O
N
T
*1: Power of two or three times the rating 80 W may be consumed during power-on, so select a power
supply with specifications that prevent a power failure.
SYNC
*2: Use the supplied RS-422 control cable connector (PRC05-P12F/TAJIMI).
*3: Connect power supplied from a UL-approved AC adapter or the secondary side safety circuit of a UL-
approved power supply circuit.
(Unit : mm)
198
1-2.Pin assignment
CONT. connector: PRC05-R12M/TAJIMI
Pin No.
A
A
B
D
A
164.5
E
J
Korea : 캐논코리아 컨슈머 이미징 ( 주 ) 사업개발팀 프로솔루션파트
대표전화 : (82)2-2191-8500
South and Southeast Asia : Canon Singapore Pte. Ltd. REG ICP Sales & Marketing Div.
Tel:+65-6799-8888
Europe/Africa/Middle East : Canon Europe Ltd. Broadcast Products Div.
Tel:+44(0)20-8588-8140
Oceania: Canon Australia Pty. Ltd. CCI Div.
Tel:+61(0)2-9805-2000
Step 2 Installation Precautions
2-1. Panning and tilting range
※ Note：
2-1-1. Panning range
The panning range extends 170 degrees to the
left and right. This yields a turning range with a
620 mm diameter which should be taken into
account when selecting the installation loca-
tion.
2-1-2. Tilting range
The tilting range is approximately 430 mm when the pan-
tilt head is inclined upward at an angle of 30 degrees and
downward at an angle of 50 degrees: this should be taken
into account when selecting the installation location.
Cable
25
t
2
Floor surface
WARNING
Do not turn the lens toward the sun. When intense light enters at the TELE side, this can cause damage
to the lens and the camera.
2-2. Installing a lightning rod
If precautions need to be taken against lightning in case the system is to
be installed on a hill-top or other such location, provide a lightning rod as
shown in the figure.
Make sure that the system will not touch the lightning rod when the
camera is panned.
In the case of a permanent installation, safety is further enhanced by
providing a lightning-proof transformer for the system's power supply.
© 2015.05 CANON INC.
DC power supply
RS-422
*2
Max.70m
HD-SDI
Cable compensator
SD
(Commercially available)
The maximum cable length
depends on the compensation
performance.
Input/output
Signal name
Input
RX+
Output
TX+
Ｃ
Input
RX–
Ｇ
Output
TX–
GND
팩스 : (82)2-2191-8576
Fax:+44(0)20-8588-8929
The panning and tilting ranges may be off by 5% or so due to variations in the
magnification caused by focusing and the pan-tilt head mounting error. Check the actual
panning and tilting ranges before proceeding to set to the subject.
Center of
PAN rotation
*3
Cable
(Provided by
the dealer)
*1
●
BU-47H
MIC
Washer
(Commercially
available)
AUX connector:
HR10A-10R-10S(71)/HIROSE
1
FPU
2
AUX1
Ａ
Ｂ
3
AUX2
Ｄ
Ｅ
Ｆ
4
AUX3
Ｈ
5
AUX4
Ｊ
Ｋ
6
COM
Ｍ
Ｌ
7
8
9
10
Center of
TILT rotation
45°
Lightning rod
3/6
Advertisement
