Tools Required: • Two 9/16” wrenches • One Phillipps screwdriver What’ s in the box Item Qty. Main Press core assembly 1 per unit Mounting feet 2 per unit Screen Clamp assembly 1 per unit 16” x 16” MDF platens with neck 1 per unit 1 per unit Hardware kit...
Page 4
Step 1 Install the Mounting feet (4) to the main press core with the supplied hardware. Two 9/16” wrenches are required for this step. Note: Refer to Page 2 for hardware detail.
Page 5
Step 2 Mount the press base to a sturdy table top with supplied mounting screws. Press is shown mounted on a Riley Hopkins 1-station press cart (sold separately). A Phillips screwdriver is required for this step. Note: Refer to Page 2 for hardware detail.
Page 6
Step 3 Install the screen clamp assembly with the supplied hardware into the slots of the off-contact brackets. One 9/16” wrench is required for this step. Name/ID Description Qty. PRSA-JRCLAMP Riley Junior Press Clamping Head assy. PRHD-WA3/8USSPFC9ZY 3/8 PFC9 Yellow Zinc USS Flat Washer PRHD-HN3/8NCGR5ZC 3/8-16Hex Nut Zinc...
Page 7
Step 4 Install the platen assembly (1) onto the tubular arm of the press. When platen is in desired location, first lock down the side knob (2). Lastly, tighten down the lower locking knobs (3). The platen can be adjusted front-to-back to help position the image onto the desired location of the substrate.
Page 8
Step 5 Set up screen. First lock the screen in place with the screen clamping knobs (1). It is ideal to fully seat the screen into the back of the screen clamp as shown. Next, loosen the off-contact nuts (2) with a 9/16” wrench. Set the desired off-contact position and retighten the nuts.
Page 9
PRTB-JNR1X1 Riley Hopkins Junior 1 color, 1 station screen printing press Name/ID Description Qty. PLWD-WIN16X16N-LOW Riley Junior Press Platen assy. w/Lowpro bracket PRSA-JRCLAMP Riley Junior Press Clamping Head assy. PRCO-KNBFLT3/8NC4ML Riley Hopkins Screen Clamp Head Knob PRSA-JR1STNPNTHED 1-station Junior Series Printhead, No Micro...
Page 10
PRSA-JRCLAMP Riley Hopkins Junior Screen Clamp assembly Name/ID Description Qty. PRCO-KNBFLT3/8NC4ML Riley Hopkins Replacement Clamp Head Knob PRHD-JN3/8NCGR5ZC 3/8-16 Hex Finish Jam Nut PRHD-HN3/8NCGR5ZC 3/8-16 Hex Finish Nut PRHD-WA3/8USSPFC9ZY 3/8 PFC9 Yellow Zinc USS Flat Washer PRHD-BTN3/8NC1BLK 3/8-16 x 1 Button Head Allen Bolt Black Oxide...
Page 11
Ryonet® will repair or replace, as Ryonet® elects, covered defective parts, materials, or workmanship without charge for parts or the reasonable cost of labor related thereto. Ryonet® will use only new or re-manufactured parts or components furnished by Ryonet® or a Ryonet®-authorized third party.
IN NO EVENT SHALL RYONET OR ANY AFFILIATE OF RYONET® BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR INJURIES TO THE FULLEST EXTENT...
Page 13
NOTES: NOTE: Logos, graphic elements and or photo images contained in this document may not be reproduced without the written consent of Ryonet...
Need help?
Do you have a question about the Riley Hopkins Junior and is the answer not in the manual?
Questions and answers