Related Manuals for Ryonet Riley Hopkins 350
Summary of Contents for Ryonet Riley Hopkins 350
- Page 1 Assembly Instructions 4 color, 4 station | 6 color, 4 station 6 color, 6 station | 8 color, 6 station...
-
Page 2: Tools Required
Tools Required: • Two 9/16” wrenches • Hammer What’ s in the box Item Qty. 1 per unit Main Press core assembly 1 per station 16” x 24” Honeycomb aluminum platen 1 per station Print station assembly 1 per station / Print station &... - Page 3 PRSA-RHCLRARMKIT Riley Hopkins Print head bumper assembly Name/ID Description Qty. Air Hose for Riley print head bump stops 3-1/2” PRCO-BMPRBLTCVRBLU long PRHD-WA5/16USSGR5ZC 5/16 USS Flat Washer Zinc 3/8-24 x 4-1/2” Hex Cap Screw grade 5 Zinc PRHD-HC3/8NF4-1/2GR5ZC PRHD-LNYN3/8NFGR5ZC 3/8-24 Lowpro Nyloc Nut...
- Page 4 PRSA-RH350 Riley Hopkins 350 station hardware. Name/ID Description Qty. PRHD-HC1/4NC3/4GR5ZC 3/8-16 X 1 Hex Cap Screw Grade 5 Zinc PRHD-LWA1/4ZC 3/8-16 Nyloc Nut Zinc MFLS-RRLWRWSHR 1/4” Roq Ready lower washer PRHD-RP3/16X1ZC 3/16 x 1 Roll Pin Zinc PRHD-RP3/16X1ZC 3/16 x 1 Roll Pin Zinc...
- Page 5 STEP 1 Install the lower bumper bolt assemblies. Do not overtighten hardware. Tighten just enough to hold in place. NOTE: Refer to page 2 for hardware detail Before dropping the print heads, ensure that spring hooks are engaged in the slots. The hooks must be facing upward. WARNING: EXTREME FORCE. INSTALL WITH CAUTION!
- Page 6 STEP 2 Install the Upper bumper bolt assemblies. No not overtighten hardware. Tighten just enough to hold in place. NOTE: Refer to page 2 for hardware detail...
- Page 7 STEP 3 Attach the print station top section with supplied hardware. One 7/16 inch wrench is required for installation. Harware labeled below are required per print station. Do not fully tighten at this time. Visually align the 2 small 3/16” holesup with the rotary section. Note: Refer to Page 3 for hardware detail.
- Page 8 STEP 4 Install the locating pins into the top 2 holes of the print station with a hammer. Once installed 1/2”, fully tighten the top hardware. Note: Failure to do so will shift the print station out of alignment with the other print stations.
- Page 9 STEP 5 Attach the print station lower section with supplied hardware. One 7/16 inch wrench is required for installation. DO NOT fully tighten at this time. Note: Refer to Page 3 for hardware detail.
- Page 10 STEP 6 Before the final tightening of the hardware, insert the 3/16” roll pins into the lower holes of the print station. With hardware snug, visually align drilled holes as close as possible. Tap them in approx. half way with a hammer. Fully tighten hardware after the pins are installed.
- Page 11 STEP 7 Once the clip is set into the desired tooth slot, release the spring loaded locking lever to hold the platen in place on the print station. Lock Platen Clip...
- Page 12 STEP 8 Install leveling feet and optional adjustments For uneven floors, install leveling feet (1) & adjust to stabilize the unit. To increase or decrease tension on the print station detent bracket, loosen 3/8” bolts (2) Raise detent assembly for higher tension and lowe assembly for less tension.
- Page 13 STEP 9 Setting the press in High position To set up the overall press height plus 2 inches, first remove the hardware in the front of the leg assembly. Swivel leg sections downward to align with the rear set of holes. Repeat this step for the remaining three leg assemblies.
- Page 14 STEP 10 Bearing gate adjustment. To adjust the locking tightness of the bearing gate assembly, first slightly loosen the 5/16” hardware (3) on the set screw side of the gate. To tighted the gatem turn set screw clockwise toward the stud holing bearings.
- Page 15 STEP 11 Level the screen clamping heads to the pallets. This one-time setting will work for the vast majority of printing jobs. Future adjustment may be required to accommodate “custom” platens that are much higher than standard. Image Key: 1. Ensure the print head arm is level with the print station. 2.
- Page 16 STEP 12 X/Y Micro adjustments Before adjusting registration in the print head you must first loosen the micro lock-down levers (2). To adjust front-to-back usr the turnbuckle knobs on the sides of the print head assembly (1). To adjust registration side-to-side, use the long knob on the side of the assembly (4).
- Page 17 STEP 13 Tilt/Off-Contact Micro adjustments Before adjusting off-contact (4) you must first loosen the off-contact jam knob (5). Once the desired off-contact is set, retighten the jam knob to hold in place. Before adjusting the tilt micro (1) you must loosen the tilt jam knob (2). Slowly loosen the tilt locking lever (3).
- Page 18 PRSA-RH300PNTHD Riley 300 Print head Sub assembly Name / ID Description Qty. Fluted CLAMP KNOBS 3/8-16 x 4” Male Stud PRCO-KNBFLT3/8NC4ML 4-prong thru-hole knob 3/8-24 Female PRCO-KNB4PRG3/8NFFM PRCO-KNBRCHT3/8NCFM 3/8 -16 Inch Course Ratchet Handles PRCO-BRNZB3/8ID1/2LG SINTERED BRZ BUSHING (SBB FL38 08) PRCO-RDED5/16LHML 5/16”-24 LEFT HAND THREAD MALE ROD ENDS PRCO-KNBTNBKL5/16NF...
- Page 20 NOTE: Logos, graphic elements and or photo images contained in this document may not be reproduced without the written consent of Ryonet...
Need help?
Do you have a question about the Riley Hopkins 350 and is the answer not in the manual?
Questions and answers