Advertisement
2.
First
program the
1st
item
"
running
mode".
motor
emit"beep-", and the
green
LED
flashes once
(
*-
)
,
then
release the SET
key to
enter
in. Motor
emit
"beep-,
beep-",
and green LED
flashes
twice(*-·
*-),
enter
the 2nd item;
So, if
motor
sounds N tones,
and green
LED flashes
N times, that
means enter the Nth
items.
But
if
the
"N"
is bigger than
the
number "5", a long
time flash
and
long
"beep--"
tone
will represent
"5".
For
example,
if
the
situation
is
as
following:
motor sounds
1
long
tone
"beep-"and
1
short
tone"beep-",
and the
green
LED flashes
(
*
-,
* -
)
,then
please release the
key
to
enter
the
NO 6th
item.
While
motor
emit a
long
tone
and
2 short
tone(Beep--,
beep-, beep-),
and
green LED
flashes
(
*--, *-·
*-)
,
release the
key to
enter the
7th
item.
And so on.
After
the
10th
item
programmed,
it
would
enter
the
1st
item
again.
3.
After hear
the indication
voice
of corresponding programmable items
then
press
the set
key to
choose the
programmable
value(you
will
hear a
"beep" tone), the
number
of tones and
flash
times
of red LED mean
the
serial number
of the
value you are
choosing.
All
the tones
under
this mode
are start
with two syllable
(di-du-), and
red
LED will
flash at
the same time(1
time
means
the
1st
value, 2
time means the 2nd
value
... ).
Short
of
pressing
SET
key
after hear
the corresponding prompt
tone,
it
will
reenter
the
programmable
item mode.
4.
Hold
SET key
for 3
seconds
under
programmable items,
the
motor
emit
2
long tones(di--du--),
red
and
green LED
flash
at
the
same
time
(
*-.
*-)
,
this
means
it is
going to
enter
the parameter storage
precedure.
Wait
for another
1 second,
motor
emit 1 long tone(du--),
red
and
green
LED
flashes
once
at
the
same
time,
this
means
t11e storage finished,
release
the SET key, switch
off
the
ESC,
it can
work
normally
when
re-energized.
Attention:
1.
A short prompt
tone
will
emit
after
press the
SET
key each time.
This
just means pressed the key
already,
but no
flash.
2.
The prompt
tone
in
programmable
items mode
are all
with the green LED
flashes. While the
tone
in the
options
of
programmable
value
mode
are
with the red LED
flashes.
3.
The parameter
value can
be updated
through
SET
key
every
energization.
4. The
parameter
value
can
be stored only under the programmable item
mode
to press the SET
key
for a
long time.
[ Reset All Items To Default Values)
1.
Turn on
the transmitter.pull the throttle stick to the maximum
position,
then switch
on
the
ESC.
2.
Wait
for 6 seconds, motor sounds
a
long tone(beep--),
press the
"SET" button
on the ESC.
3. Hold SET key for 3 seconds, motor sounds 2
long
tone(beep-,beep--),this
means
ESC
enters into
the
parameters stored
procedures.
Wait for another
1
second
when
hear
1
long
tone
it means the restores
finished.
At
this
moment
release the
SET key
and
throttle stick,
it
can work normally
after
separated.
[LED STATUS AND ALERT TONES]
1.
In
normal use,
if
the
throttle
stick
is
in
the
neutral
range,
neither the
red
LED
nor
the
green
LED
lights.
2.
The
green
LED flashes quickly
when the car
is running
forward,
while red
LED
lights
when the
car
is braking
and
it will
flash
quickly
when car
run backward
..
3.
When
the over-heat
protection happens,
the green LED
will flash
and
1 alert
tone
will be
emitted
every 2
seconds.
4. Battery
voltage
protection.
The red
LED
flashes,
and
1
alert
tone(beep) emitted every
1
second:
5.
When the ESC
can't
detect
the
normal
throttle
signal,
the
red
LED flashes, and
2
alert
tones(beep, beep)
emitted every
1
second.
A Special
Instructions
About Batteries
Contents:
1.
Keep batteries/storage batteries
out
of
reach of children.
2. Do not let batteries
lie
around openly.
There
is
a
risk
of
batteries being swallowed by children or pets.
In such
case,
seek instant medical
care!
3.
Batteries/rechargeable
batteries
must never
be
short-circuited, taken
apart or
thown
into
fire.
They
might
explode!
4.
Leaking
or
damage
batteries/rechargeable
batteries might
cause
acid
burns when getting
into contact
with
skin.
Therefore, use
suitable protective
gloves.
5.
Conventional
batteries
must
not be recharged.
Danger of
fire
and
explosion
I Only
charge
rechargeable
batteries
which
are
intended
for
this
purpose, use
suitable
rechargeable
battery
chargers.
6.
Please
observe
correct
polarity
of
batteries/rechargeable
batteries
and
the connection
of
a re-chargeable
battery
pack(note
plus/+ and
minus/-)
when inserting the
batteries.
7. If the device is not used
for
a longer period
of
time (
eg
storage), take
out
the
inserted
batteries/
rechargeable batteries
of
the
remote control
to avoid damage
from leaking
batteries/rechargeable
batteries.
Recharge
the rechargeable
battery
about
every
3
months,
because otherwise there
may
a
so
called
deep
discharge
because
of the self discharge,
which
makes
the rechargeable
batteries
useless.
8.
Always
exchange
the entire set of
batteries
or rechargeable batteries.
Do not mix full batteries/rechargeable batteries
with half-full
ones.
Always
use
batteries
or
rechargeable batteries
of
the same type
and
manufacturer.
9.
Never
mix batteries and
storage batteries.
Either
use four
batteries
or
four
rechargeable batteries
for the
remote control/transmitter.
Please Note:
Before
the
rechargeable
battery
pack delivery
its
maximum
power,
several
complete
dis-charge
and
charge cycles are
necessary.
Always
drive
the rechargeable
battery
pack
empty, since recharging
a
"half
-
full"
rechargeable
battery
pack
can
cause a
so
called
memory
effect.
That means
that
the
rechargeable battery
pack
loses its
capacity,
it
no
longer
releases
all
of its saved
energy, drive
time is decreased.
If you
are
using
several rechargeable
battery packs or
rechargeable batteries, purchasing
a
high
quality
charger maybe
worthwhile.
They are
normally also
suitable
for
fast charging of
rechargeable
batteries.
For
this purpose, proceed as
follows:
If
the
rechargeable battery pack was
taken
directly
from
the vehicle and
is
still
hot, wait
until
the
rechargeable battery
pack
has cooled down
before you
recharge. (min. of
5-10
minutes)
Connect the
plug-in
charger
with
a proper mains socket.
Connect the
rechargeable battery pack with
correct
polarity
with
the
plug-in
charger.
Normally the
special design
of
the
two
plugs
avoids
the
incorrect
connection
of the
rechargeable
battery.
Advertisement
