Advertisement
[-
0 0
-
0
Bollcry
I-xx
2-3celts
+
o
Brushless ESC S
0
l•XX~·9cul=
~
0
DC:6-12.6
[]
t
l
.
\
SET
IQJ
~
w
•
0
11
0
00
Cf12000
s+-
Receiver
[PROGRAM THE ESC]
Easily programmed
with
the
"SET" button.
Programmable Items List
Programmable
Items
Oplion1
Forward
Running
Mode
with
Oplion2
Forward
and
Reverse Force
,_Mi••
Brake
Force
•m•••
Drag brake
force
Neutral
range
Start
mode
Timing
Battery
voltage
--+--~-
protection
Over-heat
protection
Protection
mode
75
%
20
%
normal
10°
Li-xx
3.0V/cell
No protection
Remark:
The highlightened
are the
default
parameters.
Switch
~
[Servo]
80
%
100%
40
%
Options
Option6
100
%
70%
20°
Li-xx
3.4V/cell
100
%
Explanation
for each programmable item.
1.
2.
3.
Running mode:
With
"Forward with
Brake"
mode,
the
car
can
go
forward
and brake, but
cannot
go
backward, this mode is
suitable for
competition; "Forward/Reverse'
mode,
the
car only can go
forward and
backward, no
brake,
this
mode
is
usually
used
for the
Rock
Crawler.
"Forward/Reverse with
Brake" mode,
which
is
suitable
for daily training.
When move
the throttle stick from forward
zone
to
backward
zone
for
the
first
time (The 1st
"click"}, the ESC
begins
to
brake the
motor,
the motor speeds
down
but
it is
still
running,
not
completely
stopped,
so
the backward
action
is
NOT
happened
immediately.
When the
throttle
stick
is
moved
to the
backward zone again (The 2nd
"click"},
if
the motor speed is slowed
down to zero
(i.e. stopped}, the
backward action will
happen.
The
"Double-Click"
method
can prevent
mistaken reversing action when
the
brake
function
is frequently
used
in steering. By the
way, in the process
of
brake
or
reverse,
if
the
throttle
stick
is
moved
to
forward zone, the
motor
will
run forward at
once.
Reverse
Force: Sets how
much
power
will
be
applied in the
reverse direction.
Different
value
makes different
reverse
speed.
Brake
Force:
The
ESC
provides proportional brake function. The
brake
force
is
related
to the
position
of the
throttle stick.
Maximum brake
force
refers to the
force
when the throttle
stick
is located
at
the top point
of the
backward
zone. A
very large brake force
can
shorten the
brake
time,
but it
may
damage
the
gears.
4.
Drag
Brake
Force:
It's a
slight force
which caused to
motor
when
the
throttle
stick
move
to the
neutral
position.
It
is used to
slowdown the glide
speed.
5.
Throttle
Neutral Range:
It's
the
range
when
the
throtlle
stick is in
the
neutral
position but
no
output.
6. Start
Mode: It
refers to
the
start
force
of ESC, you can choose
different start
mode
according
to the
road
condition,
the tyre's ability to grip, and etc.
7.
Timing: The
"timing"
item
is
usable for sensorless brushless motors. There
are
many
differences
among
structures
and
parameters
of
different
brushless
motors,
so a
fixed
timing
ESC
is
difficult
to compatible
with
all
brushless
motors. It is
necessary to
make
the timing
value programmable. Please
select
the
most
suitable
timing
value
according to
the
motor
you
are just
using.
Generally,
higher timing value brings
out higher power
output, but the
whole efficiency
of the
system will
be slightly
lower
down.
8. Low
Voltage
Cut-Off:
The function prevents the lithium battery
pack
from
over
discharging.
It's
designed for
prolonging
its
service
life.
Here,
we
suggest
use
the
higher voltage protection
value.
9.
Over-Heat
Protection:
If
the
function
is activated,
the
output
power will
be
cut-off when
the
temperature
of
the
ESC is
higher than
a
factory-preset
value,
and the Green
LED will
flash.
While
motor will
emit
1
"beep-"
tone
every
2 seconds.
It can
recover
the output
after the
temperature
down.
10. Protection
mode:
these two method is designed
for
the lipo
battery
achieving at the
voltage
protection
value.
If
choosing cut
off
main power
immedaitely,
the
voltage
achieve
at
the
protection
value, ESC
no output.
While
if choosing lower
power,
the voltage achieve the
protection
value,
ESC will
still
have a 20%
power
output,
the
car
can
return back
slowly,
but
be
sure to
change the battery.
•Program the ESC with Set button.
First
hold
the
"SET' key, switch
on the ESC,
motor
will
sound a
"beep"
prompt
tone.
1. Hold SET
key
for 3
seconds,
it
sounds
2
long
tones(Di--,
Du--).
while
red and green LED
flash 2
times at
the
same
time
(
*
-,
*
-)
,
then
release
the key
and
wait for 0.8 seconds to enter into the
programmable
item
mode.
Advertisement
