Pressure-based air suspension control, pressure & height air suspension control (24 pages)
Summary of Contents for Ridetech LevelTow 81234006
Page 1
81234006 13-15 RAM 3500, 13 RAM 2500 Congratulations - your new LevelTow Helper Springs are quality products capable of improving the handling and comfort of your vehicle. As with all products, proper installation is the key to obtaining all of the benefits your kit is capable of delivering. Please take a few minutes to read through the instructions to identify the components and learn where and how they are used.
Page 2
FIGURE “A” PUSH-TO-CONNECT ELBOW FITTING 3/4"-16 NUT NOTE: Both illustrations are of the left, or driver’s 3/4" STAR WASHER side, of the vehicle. Reverse any orientations when assembling and installing the right, or passenger, side of the vehicle. COMBO STUD BUTTON SPRING...
Page 3
NOTE: Please read thorough this manual completely before installing the air spring kit on your vehicle. STEP 1 — PREPARE THE VEHICLE With the vehicle on a solid, level surface chock the front wheels. Remove the negative battery cable. Your vehicle is equipped with rubber jounce bumpers.
Page 4
LevelTow Compressor System Congratulations - your new LevelTow Compressor System is a quality product, that when used in conjunction with the LevelTow helper Air Springs, is capable of improving the handling and comfort of your vehicle. As with all products, proper LQVWDOODWLRQ LV WKH NH\ WR REWDLQLQJ DOO RI WKH EHQH¿...
Page 5
The LevelTow Compressor System is an automatic leveling system, once it is turned on(button illuminated blue) it will operate without any assistance. 7KH 6PDUW VHQVRU VXSSOLHG ZLWK WKH FRPSUHVVRU V\VWHP ZLOO WHOO WKH V\VWHP WR LQÀ DWH RU GHÀ DWH to keep the vehicle level.
Page 6
3. Remove the nut from the stud on the com- pressor that is sticking down. Stick the studs into the holes on the keyhole slots and slide the compressor into the locked position. Re- install the nut and tighten. Tighten the nuts on the bottom of the studs also.
Page 7
7KH DLU ¿ OWHU ZLOO QHHG WR EH PRXQWHG KLJK on the frame and out of direct tire spray. The hose on the drain should be coming straight out of the bottom. There is a drain in the bot- WRP RI WKH ¿...
Page 8
9. The sensor needs to be mounted on the frame rail with the wires pointing down. The arm will need to swing up opposite the direc- tion of the wires as the suspension is being compressed. Attach the sensor bracket to the frame with (4) self drilling screws sup- plied with the kit.
Page 9
12. The 2 pieces of heat shrink supplied in the kit will hold the linkage together after your length is determined. To apply the heat shrink slide one piece over the rubber endlink as far as it will go on to the rod side. Heat the heat shrink DW WKH UXEEHU HQG ¿...
Page 10
Keyed Power Battery (Should only have power with key on) (Needs to go to Battery under hood) Activation Manual Switch Inflate/Deflate 20 Amp Fuse White 4 pin plug Black Wire Black 3 pin plug System Ground Black Wire (these wires can be attached Relay at the same point)
Page 11
SPRINGS AIR LINE AIR LINE “T” FITTING COMPRESSOR 15. 8QFRLO WKH DLUOLQH EHLQJ FDUHIXO QRW WR NLQN RU À DWWHQ WKH OLQH. Start at the Airspring fur- thest from the compressor. Trim the airline so that the cut is clean and as square as possible. ,QVHUW WKH HQG RI WKH DLUOLQH LQWR WKH ¿...
Page 12
Manual Operation: The LevelTow Compressor System also has a manual control function. This function allows you to manually LQÀ DWHG RU GHÀ DWH WKH V\VWHP 7R XVH WKH PDQXDO IXQFWLRQ \RX PXVW ¿ UVW WXUQ WKH V\VWHP RII E\ SXVKLQJ WKH PDLQ SRZHU EXWWRQ 2QFH WKH V\VWHP LV WXUQHG RII \RX FDQ SXVK WKH URFNHU VZLWFK XS WR LQÀ...
Need help?
Do you have a question about the LevelTow 81234006 and is the answer not in the manual?
Questions and answers