Wiznet WIZ1000 User Manual
Hide thumbs
Also See for WIZ1000:
- User manual (38 pages) ,
- User manual (40 pages) ,
- User manual (38 pages)
Related Manuals for Wiznet WIZ1000
Summary of Contents for Wiznet WIZ1000
- Page 1 WIZ1000 User’s Manual (Version1.0) ©2009 WIZnet Co., Ltd. All Rights Reserved. ☞ For more information, visit our website at http://www.wiznet.co.kr...
- Page 2 WIZnet’s Online Technical Support If you want to know more about WIZnet products, please visit WIZnet website (www.wiznet.co.kr), and you could also put your questions on Q&A Board. Our engineers will reply you as soon as possible. Copyright © WIZnet All Rights Reserved...
- Page 3 Document Revision History Date Revision Changes 2009-06-26 V1.0 First Release Copyright Notice Copyright 2009 WIZnet, Inc. All Rights Reserved. Technical Support: support@wiznet.co.kr Sales & Distribution: sales@wiznet.co.kr For more information, please visit our website: http://www.wiznet.co.kr Copyright © WIZnet All Rights Reserved...
- Page 4 Trade Name or Applicant : WIZnet, Inc. Equipment Name : Serial to Ethernet Device Server Basic Model Number : WIZ1000 Manufacturer / Country of Origin : WIZnet, Inc. / KOREA Certification Number : WWW-WIZ1000-S2E(A) This equipment has been tested for a Class A digital device.
-
Page 5: Table Of Contents
6. DEMONSTRATION AND TEST ................ 34 6.1................34 ARDWARE NTERFACE 6.2............. 35 ESTING ERIAL TO THERNET UNCTION 7. WIZ1000 HARDWARE SPECIFICATION ............. 36 7.1..................36 ARAMETERS 7.2..................36 PECIFICATION 7.3............. 36 OARD IMENSIONS AND SSIGNMENT 8. - Page 6 Table 7. Serial Configuration Command Code ..........27 Table 8. Serial Configuration Testing Process ..........29 Table 9 Telnet Com Port Options List ............32 Table 10. Testing Environment of WIZ1000 ..........34 Table 11. RS-232 PIN Assignment ............37 Copyright © WIZnet All Rights Reserved...
-
Page 7: Introduction
1. Introduction WIZ1000 is one model of Serial to Ethernet Device Server which is one finished product of WIZnet with CE, FCC and KCC certifications. WIZ1000 acts as a gateway between RS-232 and Ethernet. It enables remote gauging, managing and control of a device through the network based on Ethernet and TCP/IP by connecting to the existing equipment with RS-232 serial interface. -
Page 8: Specification
1.2. Specification The specifications of WIZ1000 are introduced in Table 1. ITEM Description 8051 compliant (having internal 62K Flash, 16K SRAM, 2K EEPROM) TCP/IP W5100 (Ethernet MAC & PHY Embedded) Protocol TCP, UDP, IP, ARP, ICMP, MAC, DHCP, PPPoE, DNS... -
Page 9: Products Contents
5V Power Adaptor (Optional) Table 2. Products Contents ☞ If there is any missing item, contact to the shop where you purchased. ☞ The optional items should be purchased separately. Copyright © WIZnet All Rights Reserved WIZ1000 | 9 page... -
Page 10: Wiz1000
Block Diagram Figure 1. Block Diagram WIZ1000 is a protocol converter that transmits the data sent by serial equipment to Ethernet and converts back the TCP/IP data received through the network into serial data to transmit back to the equipment. When the data is received from serial port, it is sent to W5100 by MCU. -
Page 11: Configuration Tool
Figure 2. User Interface of Configuration Tool (Configuration via Network) ⓐ Version : Displays firmware version. The current version of the firmware of selected WIZ1000 is displayed in this field. ⓑ Enable Serial Debug Mode : If this mode is checked, you can monitor the status and socket message of WIZ1000 (listen OK, connect fail etc.) through serial terminal. -
Page 12: Figure 3. Pppoe Connection Process In Serial Console
IP Configuration Method: Select IP setting mode, you can select one from Static, DHCP, PPPoE mode. Static: “Static” is the option for setting WIZ1000 with static IP address. First select MAC address that you want to set it as static IP in ‘board list’. Then, the “Local IP, Subnet, Gateway boxes are enabled. -
Page 13: Figure 4. Tcp Server Mode
PPPoE ID/Password : If you select ‘PPPoE’ mode, input ID/Password which you received from ISP company. ⓘ Server IP/Port : When WIZ1000 is set as “Client mode” or Mixed mode”, server IP and port should be set. WIZ1000 attempts to connect this IP address. ⓙ... -
Page 14: Figure 5. Tcp Client Mode
(where WIZ1000 is installed) in order to check the status or provide the commands. In normal time WIZ1000 is on the waiting status, and if there is any connection request (SYN) from the monitoring center, the connection is established (ESTABLISH), and data communication is processed (Data Transaction). -
Page 15: Figure 6. Udp Mode
DNS(Domain Name System) is the database system having information about IP address and corresponding domain name. When connecting to domain name, you can use DNS function of WIZ1000. Input IP address of DNS server provided by ISP in DNS Server IP, and domain name in the Server (Domain) If server has dynamic IP address, but domain name, if you use DNS function, you do not need to configure server IP address whenever it’s changed. -
Page 16: Figure 7 Search Password Input Dialog
ⓜ Direct IP Address Search If there are more than one WIZ1000 in the same subnet with the same password, the function of “Direct IP Address Search” will help users to get the specified WIZ1000 by input its IP address directly. - Page 17 ⑤ To check configuration result, click ‘Search’ button. ⓟ Upload Firmware will be uploaded through network ☞ After uploading the firmware, 20~30 seconds are required for initialization. ⓠ Exit : Close the configuration tool program. Copyright © WIZnet All Rights Reserved WIZ1000 | 17 page...
-
Page 18: Figure 8. Configuration Tool (Serial Config.)
ⓡ COM Port Configuration The parameters of COM port of WIZ1000 are listed well in this page. Users can set the COM port of WIZ1000 by selecting the value of each parameter in the drop down list. ☞ By clicking the “Setting” button, selected value can be applied. - Page 19 Any one of three conditions is satisfied, the data is transmitted to the Ethernet. Ex) Delimiter: Size=10, Char=0x0D Serial data: 0123456789abc Ethernet data: 0123456789 ☞ “abc” will be remained in the serial buffer of module. Copyright © WIZnet All Rights Reserved WIZ1000 | 19 page...
-
Page 20: Figure 9. Configuration Tool (Option Config.)
‘Close’ command should be given. This function can be used for more than two or more systems to connect to a WIZ1000 module. If one system holds the connection to the WIZ1000, other systems cannot connect to the module. - Page 21 WIZ1000 and the other side. The interval can be set between 0~65535 seconds, and 0 means the keep-alive timer is disabled that no keep-alive packet will be sent.
-
Page 22: Figure 10. Option Mode For Password Configuration
The port of telnet and login password can also be defined by users. The maximum length of telnet login password is 8 bytes and its default password is ‘wiznet’. The default telnet port is Copyright © WIZnet All Rights Reserved... -
Page 23: Firmware Upload
Select a module shown in “Board list”, and click “Upload” button. ③ ☞ Before uploading through Ethernet, you should set the network information of WIZ1000 first by Configuration Tool program as shown above Fig 10. By using Ping test, Copyright © WIZnet All Rights Reserved WIZ1000 | 23 page... -
Page 24: Figure 12. Open Dialog Box For Uploading
④ “Open” button. Figure 12. Open dialog box for uploading ☞ Do not upload any other files except for WIZ1000 application firmware file. The firmware uploading status will be pop up as shown in Figure 13. ⑤ Figure 13. Firmware uploading window ⑥... -
Page 25: Serial Configuration
4. Serial Configuration 4.1. Serial Command Format It is possible to configure WIZ1000 by using serial command. By inputting specified 3 characters you can enter into the configuration mode. The characters can be defined at the Configuration Tool. <Frame Format>... - Page 26 0~65535 Set Inactivity timer value MAC Address Get MAC Address 0 : Not Use, 1 : Use Check DNS Use or Not IP address DNS IP Check Domain Domain Check Copyright © WIZnet All Rights Reserved WIZ1000 | 26 page...
-
Page 27: Table 7. Serial Configuration Command Code
0~65535 Get the server port number Get delimiter character in hex 0~255 Get delimiter size 0~65535 Get delimiter time 0~65535 Get Inactivity timer value Table 7. Serial Configuration Command Code Copyright © WIZnet All Rights Reserved WIZ1000 | 27 page... -
Page 28: Wiz1000 Configuration With Erial Ommand
4.2. WIZ1000 Configuration with Serial Command ① Check WIZ1000 Firmware version. If version is lower, download the latest firmware from download page of http://www.wiznet.co.kr Figure13. Serial Configuration Enable Setting At the default status, the serial configuration is disabled. So, click ‘enable’ check box of ②... -
Page 29: Figure 15 Serial Configuration Console Display
Above process is shown in the serial console as below figure. WIZ1000 Ver.01.00 >Config socket : OK >Listen : OK <E><S><S192.168.11.3><S> WIZ1000 Ver. 01.00 >Config socket : OK >Listen : OK Figure 15 Serial Configuration Console Display Copyright © WIZnet All Rights Reserved WIZ1000 | 29 page... -
Page 30: Telnet Com Port Options
The Telnet Com Port Option of WIZ1000 is compatible with RFC2217. A RFC2217 compliant Telnet client program can also be used to access WIZ1000. We also provide a Telnet Com Port Option client program and its user interface is shown in Figure 16. -
Page 31: Figure 17 Telnet Com Port Option Client Tool Execution Example
“DON’T” command will be replied. The Com port configuration procedure can be started only if the “DO” reply is received from WIZ1000. For each command, the value of 0 is used to query the current settings of WIZ1000. After any setting, the “Over!” button should be clicked to tell WIZ1000 that the configuration is over. -
Page 32: Table 9 Telnet Com Port Options List
Set CTS signal state ON Set CTS signal state OFF Line State Mask Refer to RFC2217 Modem State Mask Refer to RFC2217 Purge Data Refer to RFC2217 Table 9 Telnet Com Port Options List Copyright © WIZnet All Rights Reserved WIZ1000 | 32 page... - Page 33 Please note that if any Com port option command is received by WIZ1000, at least one “WON’T” command must sent to WIZ1000 to reboot it and apply the new value. WIZ1000 only replies the “WILL” and request command. If a Com port option value is received by WIZ1000, it will not reply this command but setting.
-
Page 34: Demonstration And Test
6. Demonstration and Test In this chapter, we give an example that can be used to test the function of WIZ1000 The testing environment is as below. WIZ1000 1) RS232 Port 1) WIZ1000 Device Server 2) LAN Port 2) Serial Cable... -
Page 35: Testing Serial To Ethernet Function
STEP 2: Connect the WIZ1000 to the serial device by using serial cable. STEP 3: Connect 5V DC adaptor for power supplying. 6.2. Testing Serial to Ethernet Function STEP1: Power on WIZ1000 board. STEP2: Configure the WIZ1000 by using Configuration Tool program. -
Page 36: Wiz1000 Hardware Specification
62KByte (MCU Internal) SRAM 16KByte (MCU Internal) EEPROM 2KByte (MCU Internal) 7.3. Board Dimensions and Pin Assignment 7.3.1. Dimensions 90.5 87.5 11.5 22.5 11.5 67.5 25.0 22.5 11.5 Figure 20. WIZ1000 Dimension Copyright © WIZnet All Rights Reserved WIZ1000 | 36 page... -
Page 37: Figure 21. Rj-45 Pin Assignment
Receive Data Transmit Data EXT_GND External Power Ground (Internally shorted to GND) Ground Not connect Request To Send Clear To Send EXT_VCC External Power Input (5V) Table 11. RS-232 PIN Assignment Copyright © WIZnet All Rights Reserved WIZ1000 | 37 page... -
Page 38: Warranty
WIZnet warrants our products and its parts against defects in materials and workmanship under normal use for period of standard ONE(1) YEAR for the WIZ1000 board and labor warranty after the date of original retail purchase. During this period, WIZnet will repair or replace a defective products or part free of charge.