Advertisement
Part Names and Displays
[ Meter ]
2
Note: Not display Motor RPM on Analog Display
when the Meter displays RPM by needle. See
the Digital Display to check the Motor RPM.
[ Unit ]
(View from Gauge Connection)
Connecting The Wires
Turn the power switch to Ready Mode.
Insert the OBD Connector to the Diagnostic Monitoring
Connector.
Insert the 4-pin Connector to the backside of the meter.
Insert the 5-pin Connector of Gauge Cable and 6-pin
Connector from the Power Cable to the Unit.
Placement Diagram for Diagnostic Monitoring Connector
TOYOTA
HONDA
The meter start-up and stop is differ in power connection method.
Normal
(not using IGN Cable)
Linked to the ECU
Unplug the connector of Yellow and Red cable of OBD Cable and
connect Yellow cable of IGN Cable into the connector on Yellow cable,
then connect to IGN cable to IGN of car. (Do not connect to Acc)
Notes about using the OBD Connector
M a k e s u r e t o g r i p t h e
distended portions when
pulling it out or inserting it.
How to use the Cut Connectors
1
10 mm
2
Peel of f of the vinyl
Peel off of the vinyl cover at
cover at connection.
the end of the product's wire.
2
1
Analog Display
2
Needle
3
Switch
4
Digital Display
1
5
Illumination
(night illumination)
3
4
6
Display Range
(View from Car Connection)
7
8
At the right foot of the driver seat (with lid)
At foot of driver seat in the center
At the left foot of the driver seat (with lid)
IGN
(using IGN Cable)
Linked to the power switch
CAUTION
D o n o t p u ll o n t h e w i r e s
when trying to remove the
connector; the wires may
become disconnected.
10 mm
3
Wrap around both
wire coils.
Display RPM and Motor RPM data.
Shows the current values and peak value.
Use to change modes of digital display
and reset the peak value.
Display switches between types.
Normally illuminated when on display
and Three-step dimming.
Analog Display
Digital Display
Analog Display
Digital Display
7
Meter connector
8
Power connector
9
10
Spare
9 10
1
POWER
Backside
of the
meter
4-pin
3
Connector
Meter
Holder
(1.5 m)
OBD Cable
Red
Yellow
Yellow
If you unable to get a grip
on the distended portions.
W i t h s o m e c ar m o d e l s i t
m ay b e d i f f i c u l t t o g e t a
good grip on the connector.
4
5
Close tightly with
cut connector.
Size
(See Note)
Dial & Needle : White or Blue
(Switchable)
Red
[ 0 –8000rpm ]
RPM
[0 –9000rpm ]
Motor RPM
[ - 35 – 150 °C ]
Water Temp
[ 8 – 18 V ]
Voltage
[0 –32000rpm ]
Motor RPM
Connect gauge cable
Connect OBD cable
No need to use
Ready
Mode
Diagnostic
Monitoring
Connector
4
4
Unit
6-pin
5-pin
Connector
Connector
Diagnostic
Monitoring
Connector
IGN
(12V with Key Switch ON)
IGN Cable
In such case, pull
out the connector
by p u l l i n g o n t h e
end of the zip tie.
When crimping, please
use crimpers or use pliers
to bend and then solder
Insulate with vinyl
together.
tape.
[Unit： mm]
Meter
15 30
ø60
ø65
Unit
70
50
Depth22
2
(0.5 m)
＝Cut Connector
Advertisement
