Table of Contents
Advertisement
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best performance from your new
Camera.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space
provided below. Refer to the model and serial numbers whenever you call upon your KENWOOD dealer for information or
service on the product.
Model CMOS-740HD Serial number
US Residence Only
Register your KENWOOD product at www.kenwood.com/usa/
© 2019 JVCKENWOOD Corporation
CMOS-740HD
UNIVERSAL REAR VIEW CAMERA
INSTRUCTION MANUAL
CAMÉRA DE VUE ARRIÈRE UNIVERSELLE
MANUEL D'UTILISATION
UNIVERSAL RÜCKFAHRKAMERA
BEDIENUNGSANLEITUNG
UNIVERSELE ACHTERUITRIJCAMERA
GEBRUIKSAANWIJZING
TELECAMERA PER RETROMARCIA UNIVERSALE
ISTRUZIONI PER L'USO
CÁMARA DE VISTA TRASERA UNIVERSAL
MANUAL DE INSTRUCCIONES
CÂMARA TRASEIRA UNIVERSAL
MANUAL DE INSTRUÇÕES
通用后视摄像头
使用说明书
Register Online
B5A-3444-00 (W)
Advertisement
Table of Contents
Related Manuals for Kenwood CMOS-740HD
Summary of Contents for Kenwood CMOS-740HD
- Page 1 Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial numbers whenever you call upon your KENWOOD dealer for information or service on the product.
- Page 2 Trade Name: KENWOOD Products: UNIVERSAL REAR VIEW CAMERA Model Name: CMOS-740HD Responsible Party: JVCKENWOOD USA CORPORATION 2201 East Dominguez Street, Long Beach, CA 90810, U.S.A. PHONE: 310 639-9000 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
- Page 3 Dichiarazione di conformità relativa alla direttiva EMC 2014/30/UE Dichiarazione di conformità relativa alla direttiva RoHS 2011/65/UE Produttore: JVCKENWOOD Corporation Declaration of Conformity with regard to the EMC 3-12, Moriyacho, Kanagawa-ku, Yokohama-shi, Kanagawa Directive 2014/30/EU 221-0022, JAPAN Declaration of Conformity with regard to the RoHS Rappresentante UE: Directive 2011/65/EU JVCKENWOOD Europe B.V.
- Page 4 Before Use/ Installation Procedure • Before finally installing the unit, connect the wiring WARNING temporarily, making sure it is all connected up properly, and the unit and the system work. To prevent injury or fire, take the following • When mounting this unit, make sure none of precautions: the leads are trapped between this unit and the •...
- Page 5 • Do not route wiring in places that get hot, such as WARNING near the heater outlet. If the insulation of the wiring • If you connect the ignition wire (Red) to the car melts or gets torn, there is a danger of the wiring chassis (Ground), you may cause a short circuit, that short-circuiting to the vehicle body.
- Page 6 (2 locations on each side) Adjust the angle so that the rear of the vehicle Mount so that the “KENWOOD” or the bumper can be seen at the bottom of the logo appears at the top.
- Page 7 After adjusting the camera angle, tighten the Using a grommet retaining screws firmly. CAUTION Inspect the retaining screws at times. If they are loose, tighten them firmly. • When drilling a hole in the car body to mount the camera, check the positions of fluid lines, tanks, Fix the camera firmly in position.
- Page 8 Connections CAUTION • If the engine key of your vehicle does not have the ACC position, branch the wire energized when the engine key is ON and connect it to the accessory power cord. • Before proceeding to connections, make sure that the engine key is not inserted and disconnect the (-) terminal of the battery to prevent the short-circuiting incident.
- Page 9 Information on Disposal of Old Electrical Specifications and Electronic Equipment (applicable for countries that have adopted separate waste Camera Unit collection systems) Lens Products with the symbol (crossed-out wheeled bin) cannot be disposed as Wide angle, household waste. Focal length: 1.86 mm, Old electrical and electronic equipment F value 2.0 should be recycled at a facility capable...