Hatco Powermite PMG-100 Installation And Operating Manual page 9

Booster Heater Sizing Chart (continued)
Dishmachine Model Number
INSINGER Commander 18-5, 18-5H, Ensign 40-2 . . . . . . . . . . . . . . . . . . . . . . . . . . .--- . . . . . . . . . . . . PMG-100
Admiral 44-4, 66-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PMG-100 . . . . . . . . . PMG-200
Speeder 64, 86-3, Century (all) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PMG-100 . . . . . . . . . PMG-200
Trac 321, Trac 321-2/RPW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PMG-100 . . . . . . . . . PMG-200
Trac 878 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PMG-100 . . . . . . . . . PMG-200
Clipper (all), R106-2, Super 106-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . .PMG-100 . . . . . . . . . PMG-200
Defender . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PMG-200 . . . . . . . . . . . .---
Master (all) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PMG-200 . . . . . . . . . . . .---
CA-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PMG-200 . . . . . . . . . . . .---
For outdated models, consult factory for correct booster.
*
JACKSON 44CE , 66 CERPW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PMG-200 . . . . . . . . . . . .---
54CE, 76 CERPW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PMG-200 . . . . . . . . . . . .---
64CE, 86 CERPW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PMG-200 . . . . . . . . . . . .---
100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PMG-100 . . . . . . . . . . . .---
150 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .--- . . . . . . . . . . . . PMG-100
AJ-44, AJ-66, AJ-80, WH-44, ES-4400, ES-6600
(ECOLAB/JACKSON) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PMG-100 . . . . . . . . . PMG-200
AJ-54, AJ-76, AJ-90 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PMG-200 . . . . . . . . . . . .---
AJ-64, AJ-86, AJ-100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PMG-100 . . . . . . . . . PMG-200
*
Model #44CE w/SN1999 or below requires larger booster than listed.
MEIKO K-44, K-66, K-80 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PMG-100 . . . . . . . . . PMG-200
K-54, K-76, K-90, K-64, K-86, K-100 . . . . . . . . . . . . . . . . . . . . . . . . . .PMG-100 . . . . . . . . . PMG-200
METALWASH/INTEDGE
FW4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .--- . . . . . . . . . . . . PMG-100
Shaded area indicates older models prior to Opti-Rinse.
* Hobart Model AM-12 with serial no. 12-067-357 or below and model AM-12C with serial no. 12-067-537 or below require slightly
larger booster than listed. Or C Models with serial no. 85-1041605 or greater use Opti-Rinse.
† Powermite installations above 2,000 ft. (610 m) will reduce the above capacities and may require change of pressure and/
or orifices in certain models at time of install to meet IAS safety compliance. These modifications are the responsibility of the
installer. Consult "Installation and Operating Manual" for sizing adjustments and orifice changes.
This selector chart is based on 40°F (22°C) and 70°F (39°C) temperature rises, 20 psi flow pressure, and minimum rinse cycle
timer setting in NSF listing.
All booster heaters are rated at 100% of the capacity of the dishmachines as recommended by the National Sanitation Foundation.
Where make-up water for wash tank is provided from final rinse supply, chart recommendations are based upon this additional
demand (not over 2 GPM) as required by NSF.
All sizings shown are that of the dishmachine manufacturers. Hatco Corporation is not responsible for incorrect sizing applications.
Form No. PMG100200M-0918
Powermite
Temperature Rise
40°F (22°C)
9
SPECIFICATIONS
Gas
Booster †
®
70°F (39°C)