Advertisement
C C l l e e a a n n i i n n g g D D u u c c t t l l e e s s s s V V e e n n t t i i n n g g C C h h a a m m b b e e r r
1. Remove the middle vent by gently raising up and pulling out.
2. Use the same cleaning directions as stated in "Cleaning the Hood
Canopy".
3. After cleaning, replace the middle vent.
R R e e n n e e w w i i n n g g t t h h e e E E n n a a m m e e l l F F i i n n i i s s h h
If discoloration occurs, you should thoroughly polish the finish on your hood
to renew its gloss and luster and to remove any grease residue which may
have a yellowing effect. Use any good enamel polish, refrigerator polish, or
automotive polish. C C A A U U T T I I O O N N : : D D o o n n o o t t u u s s e e a a p p o o r r c c e e l l a a i i n n c c l l e e a a n n e e r r o o r r r r o o u u g g h h
a a b b r r a a s s i i v v e e c c l l e e a a n n e e r r . .
R R e e n n e e w w i i n n g g t t h h e e S S t t a a i i n n l l e e s s s s S S t t e e e e l l F F i i n n i i s s h h
Regular cleaning is the best way to assure that your stainless steel finish stays
bright and unscratched. Use lemon oil or stainless steel polish to coat and
protect stainless steel.
B B r r a a s s s s P P a a r r t t s s
C C a a u u t t i i o o n n : : All brass special ordered parts are coated with an epoxy coating.
D D o o n n o o t t u u s s e e b b r r a a s s s s c c l l e e a a n n e e r r s s o o r r a a b b r r a a s s i i v v e e c c l l e e a a n n s s e e r r s s o o n n t t h h e e b b r r a a s s s s o o p p t t i i o o n n p p a a r r t t s s . . All
brass body parts should be wiped regularly with hot soapy water. When hot
soapy water will not do the job, use every day household cleaners that are
not abrasive.
Replacing Light Bulbs
1. Remove the bulb by rotating counterclockwise 1/4 turn. The bulb will
spring out of the socket.
2. Replace the bulb with a 50 watt GU-10 light bulb. To install the new bulb,
line up the studs on the back, push in and rotating 1/4 turn clockwise until
it falls into position.
8
Service Information
If your hood should fail to operate check to see if the the circuit breaker
is open, or if a fuse is blown?
If service is required:
1.
Call your dealer or authorized service agency. The name of
the authorized service agency can be obtained from the
dealer or distributor in your area.
2.
Have the following information readily available:
a. Model number
b. Serial number
c. Date purchased
d. Name of dealer from whom purchased
3.
Clearly describe the problem that you are having.
If you are unable to obtain the name of an authorized service agency, or
if you continue to have service problems, contact Viking Range
Corporation at (888) 845-4641 or write to:
V V I I K K I I N N G G R R A A N N G G E E C C O O R R P P O O R R A A T T I I O O N N
P P R R E E F F E E R R R R E E D D S S E E R R V V I I C C E E
111 Front Street
Greenwood, Mississippi 38930 USA
R R e e c c o o r r d d t t h h e e i i n n f f o o r r m m a a t t i i o o n n i i n n d d i i c c a a t t e e d d b b e e l l o o w w . . Y Y o o u u w w i i l l l l n n e e e e d d i i t t i i f f s s e e r r v v i i c c e e i i s s
e e v v e e r r r r e e q q u u i i r r e e d d . . The model and serial number for your hood is located
behind the filter on the left side panel in the lower right corner.
Model Number
Date of Purchase
Dealer' s Name
Address
If service requires installation of parts, use only authorized parts to
ensure protection under the warranty.
T T H H I I S S M M A A N N U U A A L L S S H H O O U U L L D D R R E E M M A A I I N N W W I I T T H H T T H H E E H H O O O O D D F F O O R R F F U U T T U U R R E E
R R E E F F E E R R E E N N C C E E
Serial Number
Date Installed
9
Advertisement
