Junked or abandoned combination beverage center/ice makers are still dangerous, even if they will sit for “just a few days.” If you are getting rid of your combination beverage center/ice maker, please follow the instructions below to help prevent accidents.
Page 3
UNDERCOUNTER CABINET CUTOUT 24” (61.0 cm)* Min. 34 1/2” (87.6 cm) Max. 35 1/8” (89.2 cm) 24” (61.0 cm) *24” width for cabinet only. 24 1/4” (61.6 cm) need for cabinet and door width clearance if door is recessed between cabinets. SPECIFICATIONS/DIMENSIONS PROFESSIONAL SERIES B B a a s s i i c c E E l l e e c c t t r r i i c c D D a a t t a a...
SPECIFICATIONS/DIMENSIONS DESIGNER SERIES B B a a s s i i c c E E l l e e c c t t r r i i c c D D a a t t a a •115 VAC/60 Hz •Maximum amps - 3.3 •Approximate shipping weight - 140 lbs (63.2 kg) Side View...
GENERAL INFORMATION U U n n p p a a c c k k 1. Remove banding from bottom of carton. Lift carton up and off of the unit. 2. Remove all tape and packaging material from the outside and inside of the cabinet. 3.
Page 6
FULL OVERLAY PANEL INSTALLATION Note: Weight of wood panel must not exceed 20 lbs. W W o o o o d d S S c c r r e e w w s s 1. A #8 pan head wood screw should be used to properly secure the wood frame. A total of 10 screws will be needed for a 3 1/2”...
Page 7
SELECTING AND PREPARING THE OVERLAY PANEL M M i i n n . . 5 5 / / 8 8 ” ” ( ( 1 1 . . 7 7 c c m m ) ) M M a a x x . . 3 3 / / 4 4 ” ” ( ( 1 1 . . 9 9 c c m m ) ) 3 3 0 0 5 5 / / 1 1 6 6 ”...
Page 8
T T O O M M A A T T C C H H E E X X I I S S T T I I N N G G C C A A B B I I N N E E T T R R Y Y T T O O E E K K I I C C K K H H E E I I G G H H T T M M i i n n .
Page 9
ATTACHING THE OVERLAY PANEL TO THE DOOR 1. If the door is attached to the unit, remove by unscrewing the top allen head set screw at the top hinge. Remove the door by angling the door off of the bottom hinge pin. 2.
National Electrical Code and applicable local codes and ordinances. The third ground plug SHOULD NOT, under any circumstances, be cut or removed. All UL listed combination beverage center/ice makers are equipped with this type of plug. WATER CONNECTION Observe and follow all local code(s) when installing appliance.
Page 11
UNDERCOUNTER 24” W. COMBINATION BEVERAGE CENTER/ICE MAKER OPERATING INSTRUCTIONS G G e e n n e e r r a a l l T T i i p p s s a a n n d d S S u u g g g g e e s s t t i i o o n n s s •After making a temperature adjustment, allow at least 2 hours for your unit to reach a new temperature setting.
Page 12
S S e e t t t t i i n n g g t t h h e e C C o o n n t t r r o o l l s s The temperature control knob is located in the grille below the door. There is a pointer on the grille at the 12:00 position to indicate knob position.
CAUTION P P r r e e p p a a r r i i n n g g t t h h e e u u n n i i t t f f o o r r s s t t o o r r a a g g e e If the unit is move, not used for an extended period of time, or will be in an area that will be near freezing temperatures, it is necessary to remove remaining water in the ice-making system.
Be sure that nothing obstructs the required air flow openings in front of the cabinet. Spiders and insects can nest in and around the combination beverage center/ice maker causing damage to the unit. Frequently brush or vacuum lint and dirt from the condenser coils for efficient performance by unscrewing the grill on the bottom front of cabinet.
TROUBLESHOOTING CHART P P r r o o b b l l e e m m Odor in cabinet Unit operates but does not produce any ice Small ice cubes Noisy operation Ice cubes sticking together. P P o o s s s s i i b b l l e e C C a a u u s s e e Interior needs cleaning.
TROUBLESHOOTING CHART P P r r o o b b l l e e m m Moisture collects on outside surface of cabinet Moisture collects inside of the unit. The unit is too warm or too cold. The unit is warm inside with the temperature control knob in the “OFF”...
Record the following information indicated below. You will need it if service is ever required. The serial number and model number for your combination beverage center/ice maker is located on the front of the unit at the base of the door frame.
Page 18
For the name of your nearest authorized Viking Range Corporation service agency, call the dealer from whom the product was purchased or Viking Range Corporation. I I M M P P O O R R T T A A N N T T : : Retain proof of original purchase to establish warranty period.
Page 19
For the name of your nearest authorized Viking Range Corporation service agency, call the dealer from whom the product was purchased or Viking Range Corporation. I I M M P P O O R R T T A A N N T T : : Retain proof of original purchase to establish warranty period.
Page 20
Viking Range Corporation 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For product information call 1-888-VIKNG1 (845-4641) or visit the Viking Web Site at vikingrange.com F20404A 41009271 Rev B (PS0806VR)