Page 1
ORDER NO. MD0808009CE Home Theater Audio System SC-HTR310P Colour (K)... Black Type Specification I Amplifier Section Power supply AC 120V, 60 Hz RMS output power of each channel driven Power consumption 10% total harmonic distortion Main set 68 W 70 W per channel (4 Ω)
SC-HTR310P 1 Safety Precautions 1.1. General Guidelines 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2. After servicing, ensure that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
Page 4
SC-HTR310P 1.2. Before Repair and Adjustment Disconnect AC power, discharge ac capacitors C5712, C5808, C5805, C5813, C5816, C5824, C5517, C5516, C5508, C5509, C5510, C5511, C5512 and C5513 through a 10Ω, 1W resistor to ground. DO NOT SHORT-CIRCUIT DIRECTLY (with a screwdriver blade, for instance), as this may destroy solid state devices.
Page 5
SC-HTR310P 1.5. Caution for fuse replacement...
SC-HTR310P 2 Prevention of Electro Static Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor “chip”...
SC-HTR310P 3 Handling the Lead free Solder 3.1. General description about Lead Free Solder (PbF) The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this equipment in considering the globally environmental conservation.
SC-HTR310P 5 Self Diagnosis Display Function This unit is equipped with the self diagnosis display function, during servicing. which alarms faulty operation with error code. Use this function 5.1. Automatically Displayed Error Codes An error code automatically appears on the display (LCD) when faulty operation is detected. Refer to Fig. 5.1.
Page 26
SC-HTR310P LCD display Symptom Cause and Remedy NOT POSSIBLE FOR THIS PCM — You cannot use Dolby Virtual Speaker, SOURCE Dolby Pro Logic and SFC effect with PCM (Scrolling) signals with sampling frequency over 48 kHz. SFC is not available for multi-channel...
Page 27
SC-HTR310P 5.3. Activating Self Diagnosis Function (Servicing Mode) This mode can be used during servicing. 1. Plug the AC adapter to the power source. Press and hold down the [VOL +] button and the [VOL -] button, and then press the [POWER] button at the same time.
Page 28
SC-HTR310P 5.4. Activating Self Diagnosis Function (Doctor Mode) This mode can be used during servicing. 1. Plug the AC adapter to the power source. Press and hold down the [INPUT SELECTOR] button and the [VOL +] button, and then press the [POWER] button at the same time.
SC-HTR310P 6 HDMI Checking Method 1. Connection of HDMI system 2. Check of HDMI Sound a. Using the [DVD AUDIO TEST DISC V-612] and DVD-VIDEO disc with Dolby Digital signal. b. [DVD AUDIO TEST DISC V-612] - Track No. 92 (96kHz, 5.1ch). Track No. 40 (Zero) Check the Level and Noise, output from L / C / R / SL / SR / SW / speaker or pin.
Page 30
SC-HTR310P 1. Connect directly DVD player to TV. 2. Connect DVD player to set then connect it to TV. 3. Do the comparison for (1) and (2) if same, it is OK.
SC-HTR310P 7 Assembling and Disassembling 7.1. Caution “ATTENTION SERVICER” Be careful when disassembling and servicing. Some chassis components may have sharp edges. Special Note: 1. This section describes the disassembly procedures for all the major printed circuit boards and main components.
Page 32
SC-HTR310P • Replacement of Diode (D5802) • Replacement of Diode (D5803) • Disassembly of HDMI P.C.B. • Disassembly of DSP P.C.B.
Page 33
SC-HTR310P 7.2. Disassembly flow chart The following chart is the procedure for disassembling the casing and inside parts for internal inspection when carrying out the servicing. To assemble the unit, reverse the steps shown in the chart below.
Page 34
SC-HTR310P 7.3. Main Parts Location Diagram (Amplifier unit)
Page 35
SC-HTR310P 7.4. Main Parts Location Diagram (Rack Cabinet)
Page 36
SC-HTR310P 7.5. Disassembly of Front Net Frame Step 1 : Insert Steel Rule in between Front Net Frame and Rack Cabinet as arrow shown. Step 2 : Slightly push the Steel Rule as arrow shown to push out the Front Net Frame.
Page 37
SC-HTR310P 7.6. Disassembly of Front ornament (L) • Follow the (Step 1) - (Step 3) of item 7.5. Step 1 : Remove 1 screw. Step 2 : Insert the screwdriver with Cloth in between the Rack Cabinet and the Front Ornament (L), and slightly push the screwdriver as arrow shown to release the Bosses in order of sequence.
Page 38
SC-HTR310P 7.7. Disassembly of Side Board Assy (L) • Follow the (Step 1) - (Step 3) of item 7.5. • Follow the (Step 1) - (Step 3) of item 7.6. Step 1 : Pull the Side Board Assy (L) to release the bosses as arrow shown.
Page 39
SC-HTR310P 7.8. Disassembly of Sub Woofer Left (SP2) • Follow the (Step 1) - (Step 3) of item 7.5. • Follow the (Step 1) - (Step 3) of item 7.6. • Follow the (Step 1) - (Step 2) of item 7.7.
Page 40
SC-HTR310P 7.9. Disassembly of Front ornament (R) • Follow the (Step 1) - (Step 3) of item 7.5. Step 1 : Remove 1 screw. Step 2 : Insert the screwdriver with Cloth in between the Rack Cabinet and the Front Ornament (R), and slightly push the screwdriver as arrow shown to release the Bosses in order of sequence.
Page 41
SC-HTR310P 7.10. Disassembly of Side Board Assy (R) • Follow the (Step 1) - (Step 3) of item 7.5. • Follow the (Step 1) - (Step 3) of item 7.9. Step 1 : Pull the Side Board Assy (R) to release the Bosses as arrow shown.
Page 42
SC-HTR310P 7.11. Disassembly of Sub Woofer Right (SP2) • Follow the (Step 1) - (Step 3) of item 7.5. • Follow the (Step 1) - (Step 3) of item 7.9. • Follow the (Step 1) - (Step 2) of item 7.10.
Page 43
SC-HTR310P 7.12. Disassembly of Centre speaker (SP1) • Follow the (Step 1) - (Step 3) of item 7.5. Step 1 : Remove 3 screws. Step 2 : Prepare a Box. Step 3 : Remove the Centre speaker unit and place on the box.
Page 44
SC-HTR310P Step 5 : Remove 6 screws. Step 6 : Remove the Centre speaker panel as arrow shown. Step 7 : Detach the White (+) and Blue (-) speaker wires. Step 8 : Remove 4 screws. Step 9 : Remove the Centre speaker (SP1) as arrow shown.
Page 45
SC-HTR310P Caution : During reassembling procedures, ensure the cable are properly dressed.
Page 46
SC-HTR310P 7.13. Disassembly of Front Left speaker (SP1) • Follow the (Step 1) - (Step 3) of item 7.5. • Follow the (Step 1) - (Step 3) of item 7.6. Step 1 : Remove 3 screws. Step 2 : Prepare a Box.
Page 47
SC-HTR310P Step 6 : Detach the Yellow (+) and Black (-) speaker wires. Step 7 : Remove 4 screws. Step 8 : Remove the Front Left speaker (SP1) as arrow shown. Caution : During reassembling procedures, ensure the cable are properly dressed.
Page 48
SC-HTR310P 7.14. Disassembly of Front Right speaker (SP1) • Follow the (Step 1) - (Step 3) of item 7.5. • Follow the (Step 1) - (Step 3) of item 7.9. Step 1 : Remove 3 screws. Step 2 : Prepare a Box.
Page 49
SC-HTR310P Step 5 : Remove the Front speaker panel as arrow shown. Step 6 : Detach the Grey (+) and Blue (-) speaker wires. Step 7 : Remove 4 screws. Step 8 : Remove the Front Right speaker (SP1) as arrow shown.
Page 50
SC-HTR310P 7.15. Disassembly of Front Baffle Assembly • Follow the (Step 1) - (Step 3) of item 7.5. Step 1 : Push the Glass door holder. Step 2 : Open the Glass door as arrow shown. Step 3 : Tilt the Shelf board (R) up slightly and remove it as arrow shown.
Page 51
SC-HTR310P Step 4 : Detach cable at connector (CN601 and CN602) on Panel P.C.B.. Step 5 : Remove 8 screws.
Page 52
SC-HTR310P Step 6 : Prepare a Box. Step 7 : Remove the Front Baffle Assembly as arrow shown and place it on the Box.
Page 53
SC-HTR310P 7.16. Disassembly of Panel P.C.B. • Follow the (Step 1) - (Step 3) of item 7.5. • Follow the (Step 1) - (Step 7) of item 7.15. Step 1 : Remove 2 screws. Step 2 : Remove 2 screws.
Page 54
SC-HTR310P Caution : Take extra care for the locator on the Panel P.C.B. during removal and assembly of the Panel P.C.B.. Step 6 : Remove the Panel P.C.B. as arrow shown.
Page 55
SC-HTR310P 7.17. Disassembly of Amplifier Unit • Follow the (Step 1) - (Step 3) of item 7.5. • Follow the (Step 1) - (Step 5) of item 7.15. Step 1 : Remove 2 screws. Step 2 : Prepare a Box.
Page 56
SC-HTR310P Step 4 : Remove 4 screws. Step 5 : Lift up the Main Set a bit and remove the Amp Fixtures as arrow shown.
Page 57
SC-HTR310P Step 6 : Remove the main set as arrow shown. Caution : During reassembling procedures, ensure the cable are properly dressed.
Page 58
SC-HTR310P 7.18. Disassembly of Glass Ornament (L) • Follow the (Step 1) - (Step 3) of item 7.5. • Follow the (Step 1) - (Step 7) of item 7.15. Step 1 : Loosen the Screws for removing the Glass door.
Page 59
SC-HTR310P Step 4 : Remove the Glass ornament (L) as arrow shown. Caution : Be careful of losing the Pivot holder as it may fall off when the Hinge angle (L) removed from the Glass ornament (L).
Page 60
SC-HTR310P 7.19. Disassembly of Glass Ornament (R) • Follow the (Step 1) - (Step 3) of item 7.5. • Follow the (Step 1) - (Step 7) of item 7.15. Step 1 : Loosen the Screws for removing the Glass door.
Page 61
SC-HTR310P Step 4 : Remove the Glass ornament (R) as arrow shown. Caution : Be careful of losing the Pivot holder as it may fall off when the Hinge angle (R) removed from the Glass ornament (R).
Page 62
SC-HTR310P 7.20. Disassembly of Top Cabinet 7.21. Disassembly of Rear Cabinet • Follow the (Step 1) - (Step 3) of item 7.20. Step 1 : Remove 4 screws. Step 1 : Remove 9 screws. Step 2 : Remove 2 screws.
Page 63
SC-HTR310P Step 4 : Detach FFC cable at the connector (CN106) on Main P.C.B.. Step 5 : Detach FFC cable at the connector (CN2001) on HDMI P.C.B.. Step 7 : Lift up and remove the HDMI P.C.B. with the chassis from the Rear Cabinet as arrow shown.
Page 64
SC-HTR310P 7.22. Disassembly of Front Cabinet • Follow the (Step 1) - (Step 3) of item 7.20. Step 1 : Remove 2 screws. Step 3 : Remove the Front Cabinet as arrow shown. Be careful both side guides and three guides at the bottom when removing the Front Cabinet.
Page 65
SC-HTR310P 7.23. Disassembly of AC Inlet P.C.B. • Follow the (Step 1) - (Step 3) of item 7.20. Step 3 : Remove Bracket as arrow shown. Step 1 : Remove 1 screw. Step 4 : Release the one side of the Rear Cabinet as arrow shown.
Page 66
SC-HTR310P 7.24. Disassembly of Main P.C.B. • Follow the (Step 1) - (Step 3) of item 7.20. • Follow the (Step 1) - (Step 3) of item 7.22. Step 1 : Remove 4 screws. Step 5 : Flip over the AC Inlet P.C.B..
Page 67
SC-HTR310P Step 5 : Lift up Main P.C.B. and remove it forward as arrow shown in sequences (from 1-2). During reassembling procedures, ensure the P.C.B. is seated properly at the locators. Step 6 : Detach FFC cable at the connector (CN2201) on HDMI P.C.B..
Page 68
SC-HTR310P 7.25. Disassembly of D-Amp P.C.B. • Follow the (Step 1) - (Step 3) of item 7.20. • Follow the (Step 1) - (Step 3) of item 7.22. • Follow the (Step 1) - (Step 3) of item 7.23. • Follow the (Step 1) - (Step 2) of item 7.24.
Page 69
SC-HTR310P During reassembling procedures, ensure the P.C.B. is seated properly at the locators. Step 6 : Remove the wire clamper to detach the fan unit connector (CN5501) on D-Amp P.C.B.. Step 7 : Open one side of the Rear Cabinet slightly as arrow shown.
Page 70
SC-HTR310P 7.26. Replacement of Audio Digital Power Amp IC (IC5000) • Follow the (Step 1) - (Step 3) of item 7.20. Step 4 : Remove 1 screw. Step 5 : Remove the TR spring as arrow shown. Step 6 : Remove the Audio Digital Power Amp IC (IC5000) from the heat sink unit A.
Page 71
SC-HTR310P • Assembly of the Audio Digital Power Amp IC (IC5000) Step 5 : Position the bottom chassis portion into the curves according to the diagram shown. (Rotate the part at 180 Step 1 : Fix the Audio Digital Power Amp IC (IC5000) to the degrees as compared to its original position.)
Page 72
SC-HTR310P 7.27. Replacement of Audio Digital Power Amp IC (IC5300) • Follow the (Step 1) - (Step 3) of item 7.20. Step 4 : Remove 1 screw. Step 5 : Remove the TR spring as arrow shown. Step 6 : Remove the Audio Digital Power Amp IC (IC5300) from the heat sink unit A.
Page 73
SC-HTR310P • Assembly of the Audio Digital Power Amp IC (IC5300) Step 5 : Position the bottom chassis portion into the curves according to the diagram shown. (Rotate the part at 180 degrees as compared to its original position.) Step 6 : Screw 1 screw at the Chassis Portion.
Page 74
SC-HTR310P 7.28. Disassembly of SMPS P.C.B. • Follow the (Step 1) - (Step 3) of item 7.20. • Follow the (Step 1) - (Step 3) of item 7.22. • Follow the (Step 1) - (Step 2) of item 7.24. Step 3 : Remove 4 screws.
Page 75
SC-HTR310P 7.29. Replacement of Switching Regulator IC (IC5701) • Follow the (Step 1) - (Step 3) of item 7.20. • Follow the (Step 1) - (Step 3) of item 7.22. • Follow the (Step 1) - (Step 2) of item 7.24.
Page 76
SC-HTR310P • Assembly of the Switching Regulator IC (IC5701) 7.30. Replacement of Diode (D5702) • Follow the (Step 1) - (Step 3) of item 7.20. • Follow the (Step 1) - (Step 3) of item 7.22. • Follow the (Step 1) - (Step 2) of item 7.24.
Page 77
SC-HTR310P • Assembly of the Diode (D5702) Step 4 : Release the Heatsink Unit B as arrow shown. Step 5 : Remove 1 screw from Diode (D5702). Step 6 : Remove the Diode (D5702) from the Heatsink Unit B. Step 1 : Fix the Diode (D5702) from the Heatsink Unit B.
Page 78
SC-HTR310P • Assembly of the Diode (D5801) 7.31. Replacement of Diode (D5801) • Follow the (Step 1) - (Step 3) of item 7.20. • Follow the (Step 1) - (Step 3) of item 7.22. • Follow the (Step 1) - (Step 2) of item 7.24.
Page 79
SC-HTR310P • Assembly of the Diode (D5802) 7.32. Replacement of Diode (D5802) • Follow the (Step 1) - (Step 3) of item 7.20. • Follow the (Step 1) - (Step 3) of item 7.22. • Follow the (Step 1) - (Step 2) of item 7.24.
Page 80
SC-HTR310P • Assembly of the Diode (D5803) 7.33. Replacement of Diode (D5803) • Follow the (Step 1) - (Step 3) of item 7.20. • Follow the (Step 1) - (Step 3) of item 7.22. • Follow the (Step 1) - (Step 2) of item 7.24.
Page 81
SC-HTR310P 7.34. Disassembly of HDMI P.C.B. • Follow the (Step 1) - (Step 3) of item 7.20. • Follow the (Step 1) - (Step 3) of item 7.22. • Follow the (Step 1) - (Step 2) of item 7.24. Step 5 : Detach FFC cable at the connector (CN2001) on Step 1 : Remove 2 screws.
Page 82
SC-HTR310P • Assembly of HDMI P.C.B. Step 9 : Remove 2 screws. Step 10 : Remove the tape. Step 11 : Remove the HDMI P.C.B. as arrow shown. Step 1 : Place back a tape after disassembly as a diagram shown.
Page 83
SC-HTR310P 7.35. Disassembly of DSP P.C.B. • Follow the (Step 1) - (Step 3) of item 7.20. • Follow the (Step 1) - (Step 3) of item 7.22. • Follow the (Step 1) - (Step 2) of item 7.24. Step 1 : Detach FFC cable at the connector (CN1002) on DSP P.C.B..
SC-HTR310P 8 Service Position Note : For description of the disassembly procedures, see the section 7 8.2. Checking & Repairing D-Amp 8.1. Checking & Repairing Main P.C.B P.C.B Step 1 : Remove the Top Cabinet Step 1 : Remove the top cabinet Step 2 : Remove the Front Cabinet Step 3 : Remove 3 screws.
Page 85
SC-HTR310P Step 7 : Slightly lift up Main P.C.B. and shift forward Main P.C.B. as arrow shown in sequences (from 1-2). Step 9 : Remove 2 screws. Step 10 : Detach 17P FFC cable at the connector (CN5050) on D-Amp P.C.B..
Page 86
SC-HTR310P Step 16 : Remove Bracket as arrow shown. Step 13 : Remove the wire clamper to detach the fan unit connector (CN5501) on D-Amp P.C.B.. Step 14 : Open one side of the rear cabinet slightly as arrow shown. Be careful guide when removing the rear panel.
Page 87
SC-HTR310P Amp P.C.B.. Caution : Ensure the cable is attached properly. Step 18 : Remove 2 screws. Step 26 : Position Fan unit and D-Amp P.C.B. with the object Step 19 : Release the catches and remove the fan unit.
Page 88
SC-HTR310P 8.3. Checking & Repairing SMPS P.C.B • Follow the (Step 1) - (Step 8) of item 8.2. Step 5 : Connect 8P cable at the connector (CN601) on Panel P.C.B.. Step 6 : Connect 9P cable at the connector (CN602) on Panel P.C.B..
Page 89
SC-HTR310P 8.4. Checking & Repairing HDMI Step 6 : Detach 12P FFC cable at the connector (CN2201) on HDMI P.C.B.. P.C.B • Follow the (Step 1) - (Step 4) of item 8.2. Step 1 : Detach 10P FFC cable at the connector (CN106) on Main P.C.B..
Page 90
SC-HTR310P Step 8 : Connect 8P cable at the connector (CN601) on Panel 8.5. Checking & Repairing DSP P.C.B.. P.C.B Step 9 : Connect 9P cable at the connector (CN602) on Panel • Follow the (Step 1) - (Step 12) of item 8.4.
Page 91
SC-HTR310P 8.6. Checking & Repairing Panel P.C.B Step 1 : Connect 8P cable at the connector (CN601) on Panel P.C.B.. Step 2 : Connect 9P cable at the connector (CN602) on Panel P.C.B.. Step 3 : Check & repair Panel P.C.B. according to the diagram...
SC-HTR310P 9 Voltage Measurement & Waveform Chart Note: • Indicated voltage values are the standard values for the unit measured by the DC electronic circuit tester (high-impedance) with the chassis taken as standard. Therefore, there may exist some errors in the voltage values, depending on the internal impedance of the DC circuit tester.
Page 93
CD PLAY STANDBY Ref No. IC1001 MODE CD PLAY STANDBY Ref No. IC1001 MODE CD PLAY STANDBY Ref No. IC1002 MODE CD PLAY STANDBY Ref No. IC1003 MODE CD PLAY STANDBY Ref No. IC1004 MODE CD PLAY STANDBY SC-HTR310P DSP P.C.B.
Page 94
SC-HTR310P 9.1.3. HDMI P.C.B. Ref No. IC2001 MODE CD PLAY STANDBY Ref No. IC2001 MODE CD PLAY -0.2 -0.2 STANDBY Ref No. IC2001 MODE CD PLAY -0.2 -0.2 -0.2 -0.2 -0.1 -0.1 -0.2 -0.2 STANDBY Ref No. IC2001 MODE CD PLAY -0.2...
Page 95
SC-HTR310P Ref No. IC2003 MODE CD PLAY STANDBY Ref No. IC2003 MODE CD PLAY STANDBY Ref No. IC2003 MODE CD PLAY STANDBY Ref No. IC2003 MODE CD PLAY STANDBY Ref No. IC2003 MODE CD PLAY STANDBY Ref No. IC2004 MODE...
Page 96
MODE CD PLAY STANDBY Ref No. Q2008 Q2009 Q2010 Q2011 Q2012 MODE CD PLAY STANDBY Ref No. Q2016 Q2017 Q2018 QR2021 QR2022 MODE CD PLAY -0.6 STANDBY -1.1 Ref No. QR2023 QR2024 QR2025 MODE CD PLAY STANDBY SC-HTR310P HDMI P.C.B.
Page 97
SC-HTR310P 9.1.4. MAIN P.C.B. Ref No. IC101 MODE CD PLAY 0.16 0.15 0.41 0.04 0.04 STANDBY 0.01 0.01 0.02 0.01 0.01 0.01 0.43 0.04 0.04 Ref No. IC101 MODE CD PLAY 0.15 0.37 0.11 0.11 0.39 0.38 0.29 0.29 STANDBY 0.39...
SC-HTR310P 12 Notes Of Schematic Diagram (All schematic diagrams may be modified at any time with the development of new technology) Notes: S601: POWER switch. ( S602: WHISPER MODE SURROUND switch. S603: VOLUME UP switch. (+) S606: SELECTOR switch. S607: VOLUME DOWN switch.
SC-HTR310P 16 Terminal Function of IC’s 16.1. IC301 (RFKWHTR210) IC MICRO-PROCESSOR Pin No. Terminal Name Function Pin No. Terminal Name Function PCONT No Connection VCC2 Voltage Supply DETECT No Connection No Connection LINK No Connection No Connection No Connection VOL_CLK...
SC-HTR310P 18 Replacement Parts List Notes: • Important safety notice: Components identified by mark have special characteristics important for safety. Furthermore, special parts which have purposes of fire-retardent (resistors), high-quality sound (capacitors), low noise (resistors), etc are used. When replacing any of these components, be sure to use only manufacturer’s specified parts shown in the parts list.
Page 142
SC-HTR310P Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks RKPX0145 RACK CABINET ASS’Y IC1004 C0ZBZ0001546 IC CLK SWITCH 149-1 RXP0071 CASTER IC2001 C1AB00002656 IC HDMI RX XTB4+20AFJK SCREW IC2002 C1AB00002541 IC HDMI TX...
Page 143
SC-HTR310P Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks QR701 B1GBCFGG0030 TRANSISTOR D5731 B0EAMM000057 DIODE QR2021 B1GBCFJJ0007 TRANSISTOR D5732 B0BC035A0007 DIODE QR2022 B1GBCFJJ0007 TRANSISTOR D5793 B0HAMP000094 DIODE QR2023 B1GBCFJJ0007 TRANSISTOR D5797 MA2J72800L...
Page 144
SC-HTR310P Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks LB2152 J0JHC0000021 INDUCTOR CNA781 K1KA05AA0083 5P CONNECTOR LB2201 J0JHC0000012 INDUCTOR LB2202 J0JHC0000012 INDUCTOR COILS & INDUCTORS LB2203 J0JHC0000012 INDUCTOR LB2205 J0JCC0000078 INDUCTOR L271...
Page 145
SC-HTR310P Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks JK2003 K1FA119E0004 JK HDMI TERMINAL R170 D0GB272JA007 2.7K 1/10W JK5001 K4AL08B00001 JK 4 CHANNEL SPEAKER R171 ERJ3GEYJ682V 6.8K 1/10W P5701 K2AB2B000011 AC INLET...
Page 146
SC-HTR310P Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R273 D0GB153JA007 15K 1/10W R609 ERJ3GEYJ102V 1K 1/10W R274 D0GB393JA041 39K 1/10W R630 D0GB332JA007 3.3K 1/10W R275 ERJ3GEYJ103V 10K 1/10W R634 D0GB332JA007 3.3K 1/10W...
Page 147
SC-HTR310P Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R2054 ERJ3GEYJ102V 1K 1/10W R2240 D0GB101JA007 100 1/10W R2064 D0GB470JA008 47 1/16W R2241 D0GB101JA007 100 1/10W R2065 D0GB470JA008 47 1/16W R2242 D0GB101JA007 100 1/10W...
Page 148
SC-HTR310P Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R5511 ERJ3GEYJ220V 22 1/10W R5893 ERJ3RBD393V 39K 1/16W R5602 ERJ3GEYJ103V 10K 1/10W R5894 ERJ3GEYJ102V 1K 1/10W R5603 ERJ3GEYJ103V 10K 1/10W R5895 ERJ3GEYJ101V 100 1/10W...
Page 149
SC-HTR310P Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks C190 ECJ1VC1H271J 270pF 50V C367 ECJ1VC1H220J 22pF 50V C191 ECA1CAK100XB 10uF 16V C368 ECJ1VC1H220J 22pF 50V C192 ECJ1VB1H152K 1500pF 50V C369 ECJ1VC1H220J 22pF 50V...
Page 150
SC-HTR310P Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks C1012 F1H1H101A230 100pF 50V C2013 F1H1C104A041 0.1uF 16V C1013 F1H1H101A230 100pF 50V C2014 F1H1C104A041 0.1uF 16V C1014 F1H1H101A230 100pF 50V C2015 EEE1CA100SR 10uF 16V...
Page 151
SC-HTR310P Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks C2206 EEE1HA2R2SR CHIP E- 50V C5317 F1H1A474A001 0.47uF 10V C2207 EEE0JA101SP 100uF 6.3V C5318 ECJ1VB1H104K 0.1uF 50V C2208 F1H1C104A041 0.1uF 16V C5319 ECJ3YB2A104K 0.1uF 100V...