Advertisement
RC001
WORKING
R
C
ADIO
ONTROL
Radio remote control or the remote control
Radio control used for the remote operation of duct-
of cooker hoods (Fig. 13).
ed cooker hoods.
T
ECHNI I CAL DATA
- Alkaline battery powered
Technical data:
- Operating frequency
- Alkaline battery powered: 12V mod 23A
- Combinations
- Operating frequency: 433.92 MHz
- Max. consumption
- Max. consumption: 25 mA
- Operating temperature
- Operating temperature: - 20 + 55°C
- Dimensions
Working description:
O
D
PERATI I NG
ESCRI I PTI I ON
The transmitter is equipped with 5 buttons for cook-
- To light the cooker hood on or to light it off
er hood management, as specified below:
press the button:
: Light ON/OFF command.
: Motor ON (speed level 1) / OFF command.
- To increase the speed up to the fourth one
: Reduce speed.
press the button:
: Increase speed.
: 10-minute timer.
- To reduce the speed up to the second one
I
O
NI I TI I AL
PERATI I NG CONDI I TI I ON
press the button:
The manufacturer supplies the radio control unit
ready to be used with codes preset in the Factory.
The set suction speed is shown by the LED
in the perimeter extraction channel (fig. 8).
Each LED colour corresponds to a different
speed, as shown below:
First speed WHITE
Second speed LIGHT BLUE
Third speed BLUE
Fourth speed RED
OPERATION MODE
Standard confi i gurati i on:
- To go from a high speed back to the first
Standard configuration requires all "cooker hoods –
radio control - system" to be provided with the same
one press twice the button:
transmission code. In the event two cooker hoods –
radio control system are installed in the same room
- To give power to the lights or to shut them
or nearby, each system may affect the operation of
the another. Therefore, the code of one radio control
system must be changed.
down press the button:
Generati i ng a new transmi i ssi i on code:
The radio control system is provided with preset
codes. Should new codes be required, proceed as
- To set the timer up press the button:
follows: Press simultaneously buttons:
The LED on the right side will start to flash
(every 5 seconds), the hood will work for 10
minutes at the selected speed and then it
for two seconds. When Leds light on, press buttons:
lights automatically off.
If the client increases or reduces the speed
(within 5 seconds). Leds flashing 3 times indicate
while the timer is on, this is automatically
the procedure is completed.
stopped.
WARNING! This operation deletes permanently the
preset codes.
GB
: 12 V mod. 23 A
: 433.92 Mhz
: 32.768
: 25 mA
: -20 ÷ + 55 °C
: 120 x 45 x 15 mm.
Working mode:
Learni i ng the new transmi i ssi i on code:
Once the transmission code is changed in the radio
The first time the system is switched on,
control unit, the electronic central unit of the cooker
hold down the light key to set the hood
hood must be made to set the new code in the fol-
with the remote control.
lowing way:
Press the main power-off button of the hood and
If two cookerhoods-radiocontrol system are
then restore power to the electronic control unit.
installed in the same room or in the imme-
Within the next 15 seconds, press the Li i ght Button
diate vicinity, each system may affect the
to synchronise the central unit with the code.
operation of the other, due to the fact that
Reset of the Factory confi i gurati i on:
they have the same code. Therefore it will be
To restore the Factory configuration, follow the pro-
necessary to change the code of one of the
cedure described below: press simultaneously but-
radio controls.
tons
Warning: The battery should be replaced
every year to guarantee the optimal range of
the transmitter.
for 2 seconds. When Leds light on, press buttons
To replace the exhausted battery, take the
plastic lid off, remove the battery and replace
it with a new one, observing the correct bat-
tery polarities. Used batteries should be dis-
carded in special collection bins.
(within 5 seconds). Leds flashing 6 times indicate
the procedure is completed.
The appliance has an electronic device to
WARNING! This operation deletes permanently the
switch it off automatically four hours after the
preset codes.
last operation carried out.
Generating a new transmission code.
radio control is supplied with preset factory
codes.
Emergency button:
If you want to create a new set of codes,
In the event that the radio control does not work, use
proceed as follows: press and hold the UP,
the emergency button to switch the appliance off.
After any necessary repairs have been performed,
STOP and DOWN buttons simultaneously for
reset the emergency button.
2 seconds. After the LEDS light up, press the
UP and DOWN buttons within 5 seconds. The
W
ARNI I NG
LEDS will flash 3 times to indicate that the
The battery should be replaced every year to guar-
process is completed.
antee the optimal range of the transmitter.
Warning: This procedure deletes all previ-
To replace the exhausted battery, take the plastic
lid off, remove the battery and replace it with a new
ously stored codes.
one, observing the correct battery polarities.
Used batteries should be discarded in special col-
Learning the new transmission code:
lection bins.
After changing the transmission code on the
radio control, the cooker hood electronic
The below product:
control unit must be made to set the new
RC001 Radi i o Control l
code as follows: Press the emergency but-
complies with the specifications set out in the
R&TTE Directive 99/5/EC.
ton twice consecutively to cut off power to
the appliance and reset it; from this moment,
WARNING
there are 15 seconds to press the light key
Any adjustments or modifications which have not
been expressly approved by the holder of the legal
conformity certificate may invalidate the user's
so that the hood synchronises itself with
rights relating to the operation of the device.
the new code.
14
The
Rev. 0 2 6/08/14
Advertisement
