Advertisement
Don't use power tools in damp or wet locations, or
expose them to rain. Keep work area well·lighted.
(3). KEEP CHILDREN AND VISITORS AWAY. All
children and viSitors should be kept a safe distance
from work area.
(4). DON'T install
8.
use this machine in explosive,
dangerous environment.
E. MAINTENANCE:
(1). DISCONNECT machine from power source
when making repairs.
(2). CHECK DAMAGED PARTS. Before further use
of the tool, a guard or other part that is damaged
should be carefully checked to ensure that it will
operate properly and perfomr its intended function
check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation. A
guard or other part that is damaged should be
properly repaired or replaced,
(3), DISCONNECT TOOLS before servicing and
when changing accessories such as blades, bits,
cutters, etc.
(4), MAKE SURE that blade tension and blade
tacking are properly adjusted.
(5). RE·CHECK blade tension after initial cut with a
new blade.
(6). TO PROLONG BLADE LIFE ALWAYS release
blade tension at the end of each work day.
(7). CHECK COOLANT DAILY low coolant level
can cause foaming and high blade temperatures.
Dirty or week coolant can clog pump, cause crooked.
CAUTION:
Cast, low cutting rate and permanent blade failure.
Dirty coolant can cause the growth of bacteria with
ensuing skin irritation,
(8). WHEN CUTTING MAGNESIUM NEVER use
soluble oils or emulsions (oil-water mix) as water will
greatly intensify any accidental magnesium chip fire.
See your industrial coolant supplier for specific
coolant recommendations when cutting magnesium,
(9), TO PRNMT corrosion of machined surfaces
when a soluble on is used as coolant, pay particular
attention
10
wiping dry the surfaces where fluid
accumUlates and does not evaporate quickly, such
as between the machine bed and vise.
F. SPECTIFIED USAGE:
This machine is used only for general metals cutting
within the range of cutting capacity.
G. NOISE:
A weighted sound pressure level: 80 dB.
H. SAFETY DEVICE:
(1). Interlock switch on pulley cover.
As soon as the pulley cover is open, machine will
stop with the function of this switch. Do not remove
this switch from machine for any reason, and check
it's function frequently,
(2). Interlock switch on cutting area as soon as the
cover of cutting area in open, machine will stop at
once witch the function of this switch, do not remove
this switch from machine for any reason, and check
it's function frequently.
READ ALL INSTRUCTION CAREFULLY BEFORE USING THIS MACHINE. SAVE THIS MANUAL.
3. SPECIFICATION:
i MOTOR
0.55KW (3/4HP), 1HP (Option)
i
Blade Size
2360 x 19 x 0.9 (Carbon Blade)
I
160Hz
29
50
75
100 (MPM)
!
Saw Blade Speed
i
50Hz
24
41
61
82 (MPM)
I MODEL NO. CUTIING CAPACllY
G5020
[90·
I •
(mm)
205
I.
(mm)
215x205
,
1
450
! •
(mm)
143
! •
(mm)
143x115
,
I
Dimension
LxW x H (mm)
1230 x 650 x 1320
,
~I N:::-,_W_' _ G,..:.' w ' : "' . ,.:.(k.."9,,,S,-) _ _ _ _ _ _ -;--_ _ .:..16::.:5:..11.:..;8:..::5 _ _
----1,
I
'
Packing Measurement (mm)
1230 x 650 x 8201
I
~._~L~x_W~x~H~ ________ ~:~5.:..60~x54.:..;0:..x.:..2~80~ _ _ _ _ _
--J
-3-
Advertisement
