Packing List - GreenWorks GPW2000-1 Owner's Manual

PACKING LIST

PART NAME
Pressure Washer
Upper Handle
Cord retainer
Spray tip panel assy(spray
tip included)
Trigger Assembly
Spray Wand
Gun Holder
Turbo Nozzle
Spray Tip Cleaning Tool
Screw
Screw
Wheels
Washer
Pin
Axle
High pressure hose
Operator's Manual
Quick Start Guide
ERP NO.
5104402
331031635AB
341013231
311381635
31140363AB
31145363
311251635
31208363
33201671
322011628
322351635
341301936AC
32908301A
33302365
33210301A
311321936
388031635
388032635
10
PART
FIGURE
NO.
1
1
1
1
1
1
1
1
1
4
2
2
2
2
1
1
Installing the wheels Insert the axle through the wheel. WARNING: This Quick Start Guide is not a substitute for reading the operator's manual. To reduce the risk of injury or death, user must read and understand operator's manual before using this product. 1 Set-up
Slide the washer over the axle pass the pin hole. Insert the axle and wheel through the frame. Slide the washer Connect garden hose to pressure washer water intake.
the wheel assembly. over the axle and insert the pin through the hole to firmly fasten
1800 PSI / 1.1 GPM 2 Assemble pressure washer gun to spray wand.
Wheel ELECTRIC PRESSURE WASHER GPW 1800
USING DETERGENT
Axle Washer Pin Install blue or black soap nozzle. Put pressure washer detergent in detergent tank. 3 Connect desired pressure tip.
Installing the gun holder Squeeze trigger and wait approx.1 minute for soap.
Line up the screw sleeves with the holes in the upper handle and push through. 1
screwdriver (not included) until the screw is tight. Insert the screw and turn clockwise with a Phillips head 4 handle. Insert high pressure hose into trigger
SPRAY TIP SPRAY TIP APPLICATION
Red - Stream tip (0° )
0 O amount of pressure. It is best used for removing hard, stuck-on grime or dirt. The red 0 degree tip provides a straight line of spray. It provides the highest 5 water outlet connector. Connect the high pressure hose to the
Green - Narrow fan tip (25° )
The green pressure washer tip provides high versatility with its 25 degree angle tip. Referred to as the washing tip, because it provides adequate pressure to remove
25 O washer tip is designed for "sweeping" foliage or debris given its wide angle. This tip dirt from surfaces, but is designed to not damage many surfaces. This pressure is versatile due to its wide area of cleaning and strong pressure application. 6 Turn on water at outlet.
White - Wide fan tip (40° )
Installing the upper handle Push and hold the push-pin buttons on the sides of the upper cleaning with relatively low pressure. This pressure washer tip is best used for light The white 40 degree tip, referred to as the "fan" tip creates the widest area of 7 Run water hose for 30 seconds with the
handle assembly (1) as you slide the handle onto the frame (2). (1) 40 O decks and other soft or delicate surfaces. or delicate cleaning applications. It is recommended for light cleaning on wood 30 S from the tank and lines. motor in OFF position. This helps drain air
Black - Soap spray tip The black soap spray tip, is used for soap application. Soap is applied under low 8 Connect power cord to wall outlet
Push-pin (2) SOAP pressure high volume for optimum performance. Soap cannot be applied under high pressure with this machine. Extension cord not recommended.
Turbo Nozzle Tip 9 Turn on Pressure Washer
wide, depending on a distance between the tip and the surface being cleaned. The nozzle rotates in a zero to 15 degree spray pattern in a circular motion to break down tough dirt and grime. The spray pattern can cover area of 4 to 8 inches before turning power On to avoid damage IMPORTANT: Ensure water outlet is On
to the pump.
NOTE:
Do Not Return to Store Missing parts, accessories or need a service center? with an Auto Start/Stop feature. To operate: Turn the power switch to the On (I) position. AUTO ON/OFF SWITCH: This Pressure washer is equipped
Call : 1-888-909-6757 www.GreenWorksTools.com Once the trigger of the gun is depressed the unit will turn on. Pump will pressurize and shut down immediately.
Rev:02 Unit will shut off and be in standby mode when trigger is released.