Table of Contents
Advertisement
Quick Links
Advertisement
Chapters
Table of Contents
Related Manuals for RITE-HITE ELIMINATOR II 610 Series
Summary of Contents for RITE-HITE ELIMINATOR II 610 Series
- Page 1 RITE-HITE ® ELIMINATOR II and COMBOSHELTER 610 Series Dock Shelters Installation Instructions & Owner’s Manual Date of Installation: ________________________ This Manual Covers All Units Shipped 4/10 to Date PRINTED IN U.S.A. PUBLICATION ECII610 REV. 11 39500031 SEPTEMBER 2015...
- Page 2 This shall be the exclusive remedy for all claims whether based on contracts, negligence, or strict liability. Rite-Hite shall not in any event be liable for any loss of use of any equipment or incidental or consequential damages of any kind.
- Page 3 ELIMINATOR II-COMBOSHELTER II 610 SERIES TABLE OF CONTENTS The following installation instructions are a compilation of the various components needed to comprise an Eliminator II or ComboShelter II model. There may be some components included in these instructions that do not apply to the unit being installed. Below is guide to the various components included.
- Page 4 ELIMINATOR II-COMBOSHELTER II 610 SERIES ORDER OF INSTALLATION Pub. ECII 610 Rev. 11 - September 2015...
- Page 5 ELIMINATOR II-COMBOSHELTER II 610 SERIES EXPLODED VIEW This unit shown in exploded view is a standard Eliminator II. Your unit may have options which are not shown in the exploded view, depending on options chosen, and application of the unit. 1 Bottom Pad, Left 17 Screw, HWH,Slf Dr/Tap, 12-14 x ¾...
- Page 6 610 Series Eliminator II & Combo II Quality Check List Model, Eliminator™ II [610E-0003] * C4 Style Face Curtain [2862-0002] Model, Combo Drive Thru Standard Pitch C4 Pull Ropes Side Member [5656-0007] C4 Weight Pockets C-Curtain Blockouts [1322-0009] Standard Tapered Other:________________ Common Collapsible Draft Pads [4108-0004]...
-
Page 7: Table Of Contents
Optional Components Additional installation instructions may be attached depending on the options chosen, and application of the unit. Introduction Thank you for purchasing a Rite-Hite ® Eliminator™ II or Care & Maintenance ComboShelter™ II dock shelter. For other applications, Metal hoods are recommended for protection of seals... - Page 8 6 1 0 S E R I E S S I D E F R A M E Table of Contents Installation Standard File Information ......D1 These instructions illustrate how to install a set of 6"...
-
Page 9: Installation Instructions
610 SERIES SIDE FRAME 2. Measure the dock door opening. Divide this 5. Measure from the mark for the outside edge of the measurement in half and mark the centerline of the side member across the door opening the full opening at dock level. -
Page 10: Common Member
610 SERIES SIDE FRAME Instructions “Common Member” This section of these installation instructions details how “common member” side frames are installed. 1. Follow steps 1 - 4 from the standard installation procedure for the side frame that are not common with another unit. -
Page 11: Fastening Methods
610 SERIES SIDE FRAME 4" Side Frame Widths Metal Side Building 1. Reference the standard installation instructions 1. Through bolt method of attachment is required for 5656-0007 and 1531-0002 along with these this building style. It will be necessary to install a instructions before proceding. - Page 12 610 SERIES SIDE FRAME FIGURE 5 FIGURE 6 FIGURE 7 Pub. 56560007 Rev. 4 - JUNE 2014...
-
Page 13: Table Of Contents
6 1 0 S E R I E S S I D E C U R T A I N Table of Contents Installation File Information ......E1 Standard Eliminator General Precautions . - Page 14 610 SERIES SIDE CURTAIN FIGURE 2 FIGURE 3 Common Standard Member Eliminator Eliminator -Gapmaster These instructions illustrate how to install a pair of These instructions illustrate how to install a pair of Eliminator™ II Side Curtains on a common member Eliminator™-GapMaster II Side Curtains that are on a stand alone unit.
- Page 15 610 SERIES SIDE CURTAIN 2. Make sure that the velcro flap on the outside of the side curtain completely covers the velcro on the side frame. (See Figure 5) 3. Continue to align the velcro flap to the outside of the side frame velcro at the top, and continue working downward to the bottom of the side frame.
-
Page 16: Introduction
6 1 0 S E R I E S C A N O P Y S T Y L E H E A D E R Table of Contents Installation File Information ......F1 Standard Canopy Style Header General Precautions . - Page 17 610 SERIES CANOPY STYLE HEADER FIGURE 2 FIGURE 3 8. Slowly lower the front bar down allowing the “U” to 4. Push the backer board back towards the mounting take up the load. bracket. 9. Position yourself under the middle of the header 5.
- Page 18 610 SERIES CANOPY STYLE HEADER FIGURE 5 WARNING The header unit is a self supporting unit and requires proper installation because of the load imposed on the frame. Installing less than the recommended amount (5)anchors, changing anchoring locations and/or insufficient anchors installation methods will be dangerous, and have possible unit failure.
-
Page 19: Flat Pitch "Over The Sides
E610 SERIES CANOPY STYLE HEADER 13. Caulk along the entire edge of the canopy top at the Instructions building wall, making sure the ends are covered. Use a good grade of flexible caulk. Flat Pitch - Over the Sides 14. Pull the end caps, located at each end, down to cover the side frame. -
Page 20: Common Member
610 SERIES CANOPY STYLE HEADER Always verify mounting distances between header mounting brackets. Too much variances in mounting distances can cause installation problems with common member units.) FIGURE 8 2. Next, lift the top curtain/bar assembly that correspond to the other side of the common member unit. - Page 21 610 SERIES CANOPY STYLE HEADER 10. Attach the endcap seam flap. (See Figure 10) Do this by centering it between the two vertical velcro strips sewn on the endcaps front face. Starting at the bottom, align the seam flap to the bottom of the endcap and go up.
-
Page 22: Installation Instructions
610 SERIES CANOPY STYLE HEADER INSTALLATION INSTRUCTIONS/FASTENING METHODS "Drive Thru" Face Curtain Brackets Fastening Methods These instructions illustrate how to install face curtain Concrete Block or Brick Wall brackets that are required for the proper function of the C4 Style Face Curtain when applied in the "Drive Thru" Through bolt fastening is required. -
Page 23: Fastening Methods
610 SERIES CANOPY STYLE HEADER FASTENING METHODS FIGURE 11 FIGURE 12 FIGURE 13 Pub. 16100003 Rev. 6 - SEPTEMBER 2015... -
Page 24: General Precautions
6 1 0 S E R I E S C - S T Y L E C U R T A I N Table of Contents Installation File Information ......G1 C-Style Curtain General Precautions . - Page 25 610 C-STYLE CURTAIN WINDSTRAP & PULL ROPE CLEAT INSTALLATION 5. Lay the canopy top cover front flap with velcro over the newly installed curtain face and screws. Take care in positioning the flap so it is even along the front of the unit. This flap keeps the water from entering behind the front curtain.
- Page 26 610 C-STYLE CURTAIN OPERATION OF PULL ROPES Most C style curtains are factory equipped with pull ropes. This allows the curtains to be adjusted in the field to allow a wide variety of trucks heights to be serviced and sealed by the same dock and dock seal or shelter.
- Page 27 610 C-STYLE CURTAIN OPERATION OF PULL ROPES FIGURE 5 Pub. 28610002 Rev. 2 - JUNE 2014...
-
Page 28: Document Name: Date Last Revised: Revision
6 1 0 S E R I E S C 4 - S T Y L E C U R T A I N Table of Contents Installation File Information ......H1 C4-Style Curtain (Up to 15 3 Off-Grade) General Precautions . - Page 29 610 SERIES C4-STYLE CURTAIN C4 STYLE CURTAIN 15 3 OFF GRADE To do this, release the outboard flap of the side curtain from the side pads in the locations of the slits. Each slit should be 2" long. The center of the top slit should be located 3"...
- Page 30 610 SERIES C4-STYLE CURTAIN C4-STYLE CURTAIN 15'-4" OFF-GRADE AND OVER Feed the hook end of the bungee cord through 5. Once the curtain face is attached properly, finish by the fabric loop on the back side of the head attaching the face retention strap to the side frame curtain.
- Page 31 610 SERIES C4-STYLE CURTAIN C4-STYLE CURTAIN 15'-4" OFF-GRADE AND OVER C4-Style Curtain (15’-4” Off-Grade and Over) Common Member These instructions illustrate how to install a C4-style curtain face mounted 15’-4” off grade and over, is a common member on a stand alone unit and assumes that the header brackets are installed on side members.
-
Page 32: File Information
6 1 0 S E R I E S G U T T E R A S S E M B L Y Table of Contents Installation File Information ......I1 Gutter Assembly General Precautions . - Page 33 610 SERIES GUTTER ASSEMBLY GUTTER ASSEMBLY 2. Once the first tek-screw is in place, again align the one screws lands approximately 1” from the gutter from side to side, parallel to the front bar end of end cap front flap to keep it from pulling bottom edge.
- Page 34 6 1 0 S E R I E S B U M P E R Table of Contents Use 1/2" lag bolts with expansion shields, 1/2" one piece anchor bolts with expansion collar, or File Information ......J1 equivalent fastener.
-
Page 35: File Information
C O L L A P S I B L E S T Y L E D R A F T P A D Table of Contents Introduction EGM draft pad pre-assembly....1 The following installation instructions are complete for EGM draft pad installation . - Page 36 COLLAPSIBLE STYLE DRAFT PAD DRAFT PAD INSTALLATION: Align velcro at top of draft pad with velcro flap on 3A. If there is not a velcro attachment flap on the side member (and back of side curtain if applica- back of the side curtain as shown in Figure 2, ble).
- Page 37 OPTIONS INSERTED AS REQUIRED OPTIONS AVAILABLE FOR THIS UNIT: HEADER BLOCKOUTS SIDE FRAME BLOCKOUTS FOAM BACKERS FOAM BACKER BLOCKOUTS *Note these are included as required. Pub. ECII 610 Rev. 11 - September 2015...
- Page 38 ELIMINATOR II-COMBOSHELTER II 610 SERIES NOTES Pub. ECII 610 Rev. 11 - September 2015...
- Page 39 ELIMINATOR II-COMBOSHELTER II 610 SERIES NOTES Pub. ECII 610 Rev. 11 - September 2015...
- Page 40 II 610 SERIES RITE-HITE ® ELIMINATOR II and COMBOSHELTER 610 Series Dock Shelters Installation Instructions & Owner’s Manual Rite-Hite Environmental Enclosures Corporation 8900 North Arbon Drive P.O. Box 245020 Milwaukee, WI 53224-9520 Pub. ECII 610 Rev. 11 - September 2015...