Putting On The Carrying Harness; Setting The Cutting Height; Fuel And Oil; Use - Hyundai HYPT5200X Instruction Manual

ATTENTION! Left-hand thread!

Putting on the carrying harness

■
The following adjustments can be made to make sure that you can
work without becoming fatigued. The settings may vary depending on
your body size.
■
Before starting work, adjust the carrying harness
body size.
■
Balance the appliance with the fitted cutting tool so that the cutting
tool swings just over the ground without the need to move the appli­
ance with your hands.
1.) Put on the carrying harness
into place (see fig. 3a).
2.) As shown in figure 36, pull on the belt
harness centrally on your body and adjust the upper body size.
3.) To tighten the two shoulder straps, pull on the two shoulder straps as
shown in figure 3c.
4.) To ensure to the correct position of the appliance on the carrying harness,
pull the belt as shown in figure 3d.
4J
5.) Hook in the carabiner (see figs. 3e-3g) and secure it with the red
O
strap on the quick release mechanism.
4J,
6.) Now take the appliance and hang it so that the carrying lug
into the carabiner as shown in figure 3h. The carrying lug
also be moved by loosening the screw
optimum orientation of the appliance.

Setting the cutting height

■
Put on the carrying harness
section "Putting on the carrying harness").
■
Use the various belt straps on the carrying harness
optimum working and cutting position (see section "Putting on the
carr y in g harness").
■
The carrying harness is equipped with a quick release mechanism.
O
Pull on the red strap if you have to release the appliance quickly
(see fig. 3i).
& CAUTION!
■
Always use the carrying harness when working with the device. Put
on the carrying harness as soon as you have started the engine and
it is ticking over. Turn off the engine before removing the carrying
harness.

Fuel and oil

■
Use semi-synthetic 2-stroke oil and unleaded petrol at 40:1 ratio.
Mix the fuel mixture in accordance with the fuel mix table.
■
Add the respective correct amounts of unleaded petrol and 2-stroke
oil to the supplied oil/petrol mixing canister (see "Fuel mix table").
Then shake the canister well.
Fuel mix table
Mixing process: 40 parts petrol to 1 part oil
Petrol 2-stroke oil
0.5 litres 12.5 ml
■
12
to suit your
and close the clasps so that they click
, to position the carrying
8
8
©
and sliding it to achieve the
and hook in the appliance (see
to adjust the

Use

& CAUTION!
■
Please pay attention to the statutory provisions in the relevant noise
protection regulations.
Before starting the appliance, always check that:
■
The fuel system is not leaking.
■
The protective equipment and cutting equipment is complete and in
perfect working order.
■
All screw connections are firmly tightened.
■
All moving parts can move smoothly and freely.
clicks

Starting when the engine is cold

can
& CAUTION!
■
Never allow the starter pull cord to whip back. This could cause
damage.
1.) Fill the fuel tank 4E) (see also the section "Fuel and oil").
2.) Push the fuel pump (primer)
3.) Switch the On/Off switch f) to "I".
4.) Pull the choke lever
5.) Hold the appliance firmly and pull out the starter pull cord@ to the
point of first resistance. Now pull hard on the starter pull cord@.
The appliance starts.
6.) If the engine does not start, repeat step 5.
7.) As soon as the engine is running, press first the safety lock-out
0
then the throttle
If the engine does not start after several attempts, read the ''Troubleshooting
guide" section.
& CAUTION!
■
Always pull the starter pull cord@ straight out. Hold the handle of
the starter pull cord@ firmly when the starter pull cord@ retracts.
Do not allow the starter pull cord@ to whip back.
NOTE
■
At very high ambient temperatures, it is possible that even a cold
engine has to be started without using the choke!

Starting when the engine is hot

(The appliance has been turned off for less than 15-
20 minutes)
1.) Switch the On/Off switch f) to "I".
ID
2.) The choke lever
3.) Hold the appliance firmly and pull out the starter pull cord@ to the
point of first resistance. Now pull hard on the starter pull cord@. The
appliance should start after 1 -2 pulls. If the appliance still hasn't started
after 6 pulls, repeat steps 1 -7 under "Starting when the engine is cold".
40
6 times.
"I \ I " .
ID
into the position
to activate the automatic choke.
does not need to be pulled out to start a warm motor.
O
and