Related Manuals for Aurora DXE-122A-DS
Summary of Contents for Aurora DXE-122A-DS
- Page 1 USERS GUIDE DXE-122A-DS DXE-142A-DS HDMI 4K60 HDMI 2.0A 18Gbps 1x2 and 1x4 with Down-Scaling www.auroramm.com Manual Number: 200304 | Firmware Rev: X.X...
- Page 2 Please review the following safety precautions. If this is the first time using this model, then read this manual before installing or using the product. If the product is not functioning properly, please contact your local dealer or Aurora for further instructions.
-
Page 3: Table Of Contents
USERS GUIDE TABLE OF CONTENTS PACKAGE CONTENTS ................................. 3 INTRODUCTION ..................................4 About ....................................4 Features ....................................4 Front and Rear Panel ................................5 SYSTEM CONNECTION ................................ 6 Connection Procedures ............................... 6 EDID MANAGEMENT ................................7 EDID Setup ..................................7 HDCP Mode .................................. -
Page 4: Package Contents
PACKAGE CONTENTS Please make sure the following items are included within your package. Contact your dealer if any items are missing or damaged. DXE-122A-DS or DXE-142A-DS x 1 5v 1A DC Power Adapter x 1 *Note: Go to www.auroramm.com... -
Page 5: Introduction
3D formats and true 4K2K video. EDID management can be one of the most important capabilities to a splitter. Taking it one step further Aurora has added the ability to customize EDID for complete EDID emulation. This allows full control over the source and what it will be allowed to do. -
Page 6: Front And Rear Panel
USERS GUIDE Front and Rear Panel Front Power LED: Illuminates red once powered on. Input LED: Illuminates blue when HDMI input is present. Output LEDs: Illuminates blue when HDMI output is present for that port. EDID: 4 position DIP switch for setting EDID and HDCP modes. Please refer to the EDID Management section for more detail. -
Page 7: System Connection
USERS GUIDE SYSTEM CONNECTION The following diagram illustrates typical input and output connections that can be utilized with 4K HDMI Splitter: HDTV HDTV Connection Procedures Step 1 Connect a HDMI/ DVI source device (e.g., Blue-ray DVD) to the HDMI INPUT of the 4K HDMI Splitter with an HDMI cable. -
Page 8: Edid Management
USERS GUIDE EDID MANAGEMENT The Extended Display Identification Data (EDID) is used by the source device to match its video resolution with the connected display. By default, the source device obtains its EDID from the first connected display. Since it is possible for displays with different capabilities to be connected to the splitter, the DIP switch on the front panel can be used to set the EDID to a fixed value to ensure the compatibility in video resolution. -
Page 9: Hdcp Mode
USERS GUIDE HDCP Mode Put the switch 4 on the “ON” position to select HDCP Active mode, or on the “OFF” position for HDCP Passive mode. Switch Mode HDCP Passive OFF (0) Automatically follows the display’s HDCP version. (Default) Automatically removes the HDCP content of HDMI output for broader ON (1) Active video solution. -
Page 10: Connector Pin Definition
USERS GUIDE CONNECTOR PIN DEFINITION HDMI Pin 1 TMDS Data2+ Pin 8 TMDS Data0 Shield Pin 15 Pin 2 TMDS Data2 Shield Pin 9 TMDS Data0– Pin 16 Pin 3 TMDS Data2– Pin 10 TMDS Clock+ Pin 17 DDC/CEC Ground Pin 4 TMDS Data1+ Pin 11 TMDS Clock Shield... -
Page 11: Firmware Updating
USERS GUIDE FIRMWARE UPDATING Please follow the below steps to upgrade firmware by the Micro-USB port: 1. Connect the splitter to the PC with USB cable. 2. Power on the splitter, and then the PC will automatically detect a U-disk named of “BOOTDISK”. 3. -
Page 12: Troubleshooting
USERS GUIDE APPENDIX 1 Troubleshooting Problem Solution 1. No video signal a. Check that the power plug is properly inserted into a functioning power outlet. b. Make certain source is on. c. Make certain destination is on. d. Swap out HDMI cable. e. -
Page 13: Product Dimension Drawing
USERS GUIDE APPENDIX 2 Product Dimension Drawing www.auroramm.com... - Page 14 USERS GUIDE www.auroramm.com...
-
Page 15: Technical Specifications
DTS-HD Master Audio, Dolby TrueHD Dolby Digital, DTS, DVD-Audio, Audio Support LPCM, SACD, MPCM Firmware Update Mini-USB port Input 1x HDMI Output 2x HDMI (DXE-122A-DS)/4x HDMI (DXE-142A-DS) EDID 4 Pin Dip Switch with preconfigured EDID Mechanical Housing Metal Enclosure Dimensions DXE-12H-4K: 96 x 70.4 x 17.6mm (3.94”x2.76”x0.433”) [L x W x H] DXE-14H-4K:142 x 70.7 x 17.6mm (5.59”x2.76”x0.433”) -
Page 16: Cabling
HDMI cabling will result in loss of signal or artifacts in the image. HDMI 2.0A requires cable capable of 18Gbps. Aurora manufactures HDMI 2.0A cables in a variety of different colors which are highly flexible, light weight and durable. These cables are also available in a variety of lengths and can be found on the Aurora website www.auroramm.com. -
Page 17: Warranty
Limited 6 Year Warranty Aurora Multimedia Corporation (“Manufacturer”) warrants that this product is free of defects in both materials and workmanship for a period of 5 years as defined herein for parts and labor from date of purchase. This Limited Warranty covers products purchased in the year of 2019 and after. - Page 18 USERS GUIDE Aurora Multimedia Corporation 205 Commercial Court | Morganville, NJ 07751 Phone: 732-591-5800 | Fax: 732-591-6801 www.auroramm.com...