Table of Contents
Advertisement
moisture and other atmospheric influences.
INSTALLATION INSTRUCTIONS
1.
If possible avoid placing the appliance near
cookers, radiators or in direct sunlight as this
will cause the compressor to run for long
periods. If installed next to a source of heat or
refrigerator, maintain the following minimum
side clearances:
From Cookers
From Radiators
From Fridges
2.
Make sure that sufficient room, with an
average temperature of between 16°C and
32°C, is provided around the appliance to
ensure free air circulation. Ideally, a space of
no less than 9cm on the back and 2cm on the
sides.
3.
The appliance should be located on a smooth
surface.
4.
It is forbidden to use the refrigerator
outdoors.
5.
Protection from moisture. Do not locate the
freezer in moist space to avoid the metal parts
rusty. And do not spray water to the freezer,
otherwise it will weaken the insulation and
causes current leakage.
6.
Refer to "Cleaning and Care" section to
prepare your appliance for use.
7.
If the freezer is installed in unheated areas,
garages etc., in cold weather condensation
may form on the outer surfaces. This is quite
normal and is not a fault. Remove the
condensation by wiping with a dry cloth.
8.
Never place Refrigerator in a wall recessed or
into fitted cabinets or fumiture when it is
working, the grille at the back may become
hot and the sides warm. Do not drape the
Refrigerator with any covering.
STARTING TO USE
Before you starting to use the freezer, please check
that:
1.
The interior is dry and air can circulate
freely at the rear.
2.
Clean the interior as recommended
under "TAKE CARE" section (electric
parts of the refrigerator can only be
wiped by dry cloth).
3.
Do not switch on until 4 hours after
moving the fridge/freezer. The coolant
fluid needs time to settle. If the
appliance is switched off at any time,
wait 30 minutes before switching back
on to allow the coolant fluid to settle.
4.
Before connecting the Refrigerator to
the mains supply position. The
4" (100 mm)
12" (300 mm)
4" (100 mm)
thermostat control dias is located inside
the Fridge compartment.
5.
Turn the thermostat knob to the "3"
position and turn on the electricity. The
compressor and the light inside the
refrigerator will begin to work.
6.
Before storing foods in your refrigerator,
turn the refrigerator on and wait for 24
hours, to make sure it is working
properly and to allow the Fridge/Freezer
to fail to the correct temperature.
7.
Open the door 30 minutes later, if the
temperature in the refrigerator
decreased obviously, it shows that the
refrigerator system works well. When
the refrigerator operates for a period of
time, the temperature controller will
automatically set the temperature
within limits it opens.
COMBI OPERATION
Appliance connected to power at the first time:
When the appliance is connected to power at the
first time, the display will be lit for 2 seconds before
going normal and the appliance runs with
intelligence function.
Display Control: When the refrigerator door is closed
and there is no button operation in 3 minutes, the
display light goes off.
When the display light is off, open the refrigerator
door or click any button to light it up.
VERTICAL DISPLAY (Only on some models)
TEMPERATURE SETTING: Click the "Fridge" or
"Freezer" button and when it flickers in the symbol,
temperatures can be set. Each time when the button
is clicked, the temperature changes accordingly.
Temperatures cannot be set under functions of fast
cooling, fast freezing, Smart ECO and vacation. Under
temperature setting, if there is no button operation
in 5 seconds, the button stops flickering and the set
temperature comes into effect.
SMART ECO: Activate the Smart Eco button to set
the temperatures of the fridge in max. energy
efficiency conditions (+4°C for fridge temperature, -
26
Advertisement
Table of Contents
