AQUALUX Aqua 4 Manual

Half framed sail bath screen with towel rail
Hide thumbs Also See for Aqua 4:

Advertisement

Quick Links

Tools Required (not supplied)

Spirit Level
Suitable Drill Bits
6mm dia. *
3mm dia. HSS
* Ensure drill bit used is suitable for wall surface
IN00297 (rev A)
Half Framed Sail Bath Screen
with Towel Rail
Suitable for both Right and Left Hand Fixing

Before You Start

Check that the bath has been installed
correctly and that it is level (Fig. A), tiled
down onto and sealed to the manufacturerʼs
guidelines. Please Note: All product supplied
without bath.
Check that there is suffi cient space on the
bath for the product and that the screen
movement does not foul other items such as
sinks and taps.
Ensure the product is fi tted to a non-porous
surface ie. tiled. Check that the wall surface
is fl at.
Unpack and check the product is complete
and undamaged.
Fixings are supplied for solid walls only.
Ensure that the correct fi xings are used for the
wall type – if in doubt seek professional advice
Ensure the area is clean, dry and dust free.
Read the instructions in full.
Have the correct tools available, (as shown
below, see ʻTools Requiredʼ).

Safety

Handle all glass with care - support on cardboard to avoid risk of breakage.
This product is heavy and requires 2 people to carry and install it.
When drilling walls check fi rst for hidden pipes and cables.
All glass is toughened – it cannot be reworked or replaced by ordinary glass.
Use safety eyewear when drilling.
Use safety eyewear when handling glass.
Keep all small parts away from children.

Disclaimer

Please notify the retailer immediately of any damage or faults. The manufacturer cannot be
held responsible for any installation costs that may arise from damaged or faulty product being
installed.
Please dispose of all packaging with due regard to the environment.
Screwdriver
Tape Measure
Fig.A.
Pencil
Silicone Gun & Sealant
Power Drill

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Aqua 4 and is the answer not in the manual?

Questions and answers

Summary of Contents for AQUALUX Aqua 4

  • Page 1 IN00297 (rev A) Half Framed Sail Bath Screen with Towel Rail • Suitable for both Right and Left Hand Fixing Before You Start • Check that the bath has been installed Fig.A. correctly and that it is level (Fig. A), tiled down onto and sealed to the manufacturerʼs guidelines.
  • Page 2 Parts & Fittings Supplied Please notify the retailer immediately of any damage or faults. The manufacturer cannot be held responsible for any installation costs that may arise from a damaged or faulty product being installed. Keep small parts away from children Assembled Glass Screen Horizontal Seal...
  • Page 3 Wall Channel Wall Channel Stile Cap Towel Rail Assembly Loose Screws & Fittings Supplied No.8 x ⅜” Pan Head Pozi Screws No.8 x 1¾” Pan Head Pozi Screws (actual size) (actual size) Wall Plugs Screw Snap Caps (actual size) (actual size) Screw Snap Cap Base (actual size)
  • Page 4 Important Note: Ensure that Drain holes are always facing inwards. If Glass Screen is positioned with the drain holes not facing inwards, please adjust glass screen as detailed. Remove Top Drain as shown. Remove Glass Screen from Wall Stile Ensure Drain now at top is facing INWARDS iii) Reposition Drain...
  • Page 5 Tip: When drilling tiles apply masking tape to surface to stop drill bit slipping. Wall plugs supplied are for solid walls only. Ensure correct wall plug for wall type is used. If in doubt seek professional advice. Mark position of pre-drilled Position wall channel on wall.
  • Page 6 Ensure Drain is facing INWARDS Handle unframed glass with care - support on cardboard to avoid risk of breakage. Ensure drain holes are facing INWARDS. If not please refer back to page 4 to change bath screen handing. Drain holes must be facing inwards as shown.
  • Page 7 Inside View TIP: To push fi t Frame Seal, start at the corner and work across. Inside View Cut Horizontal Seal to suit...
  • Page 8 Towel Rail is supplied assembled. Use allen key supplied, disassemble part and then reassemble as shown. Ensure all screw heads are on the door interior. Only apply sealant to the outside of the Bath Screen. DO NOT use silicone sealant on inside of the Bath Screen.

Table of Contents