Advertisement
Quick Links
Advertisement
Summary of Contents for laguna LBM 200
- Page 1 LBM 200 Mortiser Manual LAGUNA TOOLS 2072 Alton Parkway Irvine, California 92606 Ph: 800.234.1976 Model Numbers: MT0LBM200 www.lagunatools.com © 2018, Laguna Tools, Inc. LAGUNA® and the LAGUNA Logo® are the registered trademarks of Laguna Tools, Inc. All rights reserved.
- Page 2 Machines sold through dealers must be registered with Laguna Tools within 30 days of purchase to be covered by this warranty. Laguna Tools guarantees all new machines and accessories sold to be free of manufacturers’...
-
Page 3: Table Of Contents
Table of contents Safety Rules Noise emission Specification sheet Receiving your machine Unpacking your machine Introduction to your machine Assembly and setup Where to locate your machine Operating your machine Maintenance Troubleshooting Accessories Electrical drawing Spare parts Exploded view drawings and parts lists... -
Page 4: Safety Rules
Safety Rules As with all machinery, there are certain hazards involved with the operation and use. Using a machine with caution will considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the operator may result. If you have any questions relative to the installation and operation, do not use the equipment until you have contacted your supplying distributor. -
Page 5: Noise Emission
Noise emission Notes concerning noise emission: Given that there exists a relationship between noise level and exposure times, it is not precise enough to determine the need for supplementary precautions. The factors affecting the true level of exposure to operators are clearly the amount of time exposed, the characteristics of the working environment other sources of dust and noise, etc. -
Page 6: Receiving Your Machine
All damage must be noted on the delivery documents and signed by you and the delivery driver. You must then contact the seller [Laguna Tools] as soon as practical. If damage is found after delivery, contact the seller as soon as practical. - Page 7 What you will receive with your machine Mitre gauge Mobility kit Optional mobility kit Mortiser with box removed Accessories Side stop main bar Introduction to your mortiser: This mortiser is designed to give you years of safe service. Please read this owner’s manual in its entirety before assembly.
-
Page 8: Assembly And Setup
Motor and moving table The motor is mounted onto a plate that moves in all three directions and angularly. Horizontal and lateral movement is achieved with a gear stick type handle. Vertical movement is achieved by operating a geared handle. Loosening 2 nuts and moving to the desired angle with the aid of a lever achieves angular movement. - Page 9 care not to stress or damage the wiring during assembly. Lift the mounting plate and slide it onto the first set of rollers. Tip the mounting plate so that it is lifted over the split pin [fitted on the lower plate] that is used as a stop. This may take some jiggling.
- Page 10 any procedure that you feel is unsafe or that you do not have the physical capability of achieving. Leveling the Mortiser After you have located your machine in its final position. You will have to level it: Place a spirit level on the worktable. You will have to level the machine in both directions.
- Page 11 Cleaning the machine Remove the rust protection grease with WD 40 or similar solvent. It is important that you remove all the grease and re lubricate with a Teflon-based lubricant as Teflon has less tendency to attract sawdust and cause clogging. You should also wax the table as this also protects the cast iron from rust.
- Page 12 Assemble the indexing barrel as shown with the screws provided, do not fully tighten, as you will have to adjust the position to suit the locking mechanism. Attach the locking pin hand grip to the end of the table movement handle and lock in position with the allen set screw.
- Page 13 Fitting the electrical cable The CEE plug and socket are located under the control box. The electrical cable is fitted as shown. You will see a wire that is yellow and green Releasing or green; this is the ground wire, and the socket cover other colored wires are power.
- Page 14 safer to test the machine without the mortiser bits fitted. Check that the red safety switch is in the fully out position. Check that the machine is clear of all tools and other loose objects. Check that all the adjusting and locking handles are tight. Start the machine by pressing the green start knob.
- Page 15 To move the mortiser to an angle. Loosen the two clamp bolts that attach the drill unit to the body of the machine and rotate the unit with the aid of the handle. Care must be Lock nut taken, as the unit is heavy. Angle Handle adjustment...
-
Page 16: Troubleshooting
All bearings are sealed for life and do not require any maintenance. If a bearing becomes faulty, replace it. Rust The machine is made from steel and cast iron. All non-painted surfaces will rust if not protected. It is recommended that they be protected by applying wax or a Teflon-based lubricant. -
Page 17: Accessories
Feeding the wood too fast. Slow down the feed rate. Machine vibrates Machine not level on the floor. Re-level the machine ensuring that it has no movement. Accessories The following accessories are available from Laguna Tools: Various drills and cutting tools. Toolbox Additional job clamps. Work Benches Additional job setting stops Tool cabinet [floor standing]. -
Page 19: Spare Parts
Spare parts Ordering spare-parts When ordering spare parts, specify: Machine model Part number required, taken from the exploded view drawings and parts lists on the following page. Quantity required EXAMPLE: To order a roller for the table: Model: LBM200 Mortiser Part description: Roller. - Page 20 LBM 200.00.00.00 BORING MACHINE FOR WOOD...
- Page 21 LBM 200.00.00.00 BORING MACHINE FOR WOOD DPM 250.01.00.00.00-L STAND M129-90-M10 HANDLE M10 WASHER ø32Хø6,5Х5 SCREW М6Х16 ISO 7380 DPM 250.02.10.18-02 FLYWHEEL ø200 DPM 250.02.10.19-02 SHAFT FS 32N.10.00.09 PIN ø6 SPRING PIN ø 5Х30 DIN 1481 FS 32N.10.00.48 WASHER FS32N.10.00.47 GEAR WHEEL Z=11...
- Page 22 SCREW М 4x8 DIN 84 К900 STARTER DIN 7980 SPRING WASHER 2-10Н WASHER АМ 10 DIN 125 A DM5-401.31.00.48 HOLLOW BOLT BOLT М 8х55 DIN 931 DIN 7980 SPRING WASHER 2-8Н DM5-321.40.00.07-01 CORPS SCREW М 6Х12 DIN 963A DPM 250.00.00.08-01 DPM 250.11.00.00-01 BOARD WITH BLOCKS DPM 250.P5 00.00-01...
- Page 23 Laguna Tools is not responsible for errors or omissions. Specifications subject to change. Machines may be shown with optional accessories. © 2018, Laguna Tools, Inc. LAGUNA® and the LAGUNA Logo® are the registered trademarks of Laguna Tools, Inc. All rights reserved.