Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Datecs LineaPro 7 Industrial
Summary of Contents for Datecs LineaPro 7 Industrial
- Page 1 1 DATECS LineaPro 7 Industrial User Manual...
- Page 2 LEGAL NOTICE THE INFORMATION IN THIS DOCUMENT CANNOT BE REPRODUCED IN ANY MECHANICAL, ELECTRICAL OR ELECTRONIC WAY AND UNDER ANY CIRCUMSTANCES WITHOUT THE WRITTEN CONSENT FROM DATECS LTD. Address: 4 Datecs Street, Sofia 1592, Bulgaria Phone: +359 2 816 55 50 Fax: +359 2 816 55 65 E-mail: export@datecs.bg...
- Page 3 1 DATECS LINEAPRO 7 INDUSTRIAL USER MANUAL REVISION HISTORY Version Data Change description 1.0.0 14.12.2017 First Release 2.0.0 10.03.2020 Added Section “Regulatory” UM 07.01.12/v1.0.0...
-
Page 4: Table Of Contents
REGULATORY ................................... 5 TECHNICAL SPECIFICATIONS ..............................6 GENERAL VIEW ..................................8 GETTING STARTED ................................. 10 ATTACHING APPLE DEVICE TO LINEAPRO 7 INDUSTRIAL ..................... 11 REPLACING BATTERY OF LINEAPRO 7 INDUSTRIAL ......................13 OPERATION MODES ................................15 ................................15 CANNING BARCODES .............................. -
Page 5: Regulatory
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. Any change or modification to the product not expressly approved by Datecs Ltd could void the user's authority to operate the device. -
Page 6: Technical Specifications
Apple iPhone 7 and iPhone 8 Audio Features Electro-Magnetic Buzzer DC 5V through USB type-C Power Supply DC 5V through Datecs charging station Rechargeable Li-Ion Battery 3.6V / 2400mAh Battery Precise battery management by Fuel Gauge microcontroller for remaining battery capacity... - Page 7 1 DATECS LINEAPRO 7 INDUSTRIAL USER MANUAL Use only original equipped DATECS cable USB-A to USB-C (Z05C000000-05) for charging Apple device. Use only UL approved USB adapters. The minimum requirements of USB adapter is 5V/2.1A! Waste Electrical & Electronic Equipment...
-
Page 8: General View
1 DATECS LINEAPRO 7 INDUSTRIAL USER MANUAL GENERAL VIEW UM 07.01.12/v1.0.0... - Page 9 1 DATECS LINEAPRO 7 INDUSTRIAL USER MANUAL 1. Barcode engine 7. Opening for 2. Back Cover 8. Linea battery cover lock/unlock lever 3. On/Off button of Apple device 9. Battery cover 4. Left and Right scan buttons 10. External features connector 5.
-
Page 10: Getting Started
LINEAPRO 7 INDUSTRIAL USER MANUAL GETTING STARTED LineaPro 7 Industrial has rechargeable Li-ion battery. Can be charge from USB port or External features connector. Before first use, battery must be fully charged. If the device is fully discharged, charging time to fully charged would be approx. -
Page 11: Attaching Apple Device To Lineapro 7 Industrial
1 DATECS LINEAPRO 7 INDUSTRIAL USER MANUAL ATTACHING APPLE DEVICE TO LINEAPRO 7 INDUSTRIAL First is need to be removed back cover. Then must be slide down iPhone to Linea Pro 7 Industrial lightning connector. UM 07.01.12/v1.0.0... - Page 12 1 DATECS LINEAPRO 7 INDUSTRIAL USER MANUAL Slide until completely fit of the iPhone to LineaPro 7 Industrial. Place back cover to LineaPro 7. UM 07.01.12/v1.0.0...
-
Page 13: Replacing Battery Of Lineapro 7 Industrial
1 DATECS LINEAPRO 7 INDUSTRIAL USER MANUAL REPLACING BATTERY OF LINEAPRO 7 INDUSTRIAL The rechargeable battery of Linea can be replaced. Put the lever (1) to unlock position, then pull up the battery cover (2). Remove old battery with pulling up. - Page 14 1 DATECS LINEAPRO 7 INDUSTRIAL USER MANUAL Insert first the side with contacting pads of the battery then press it down. Direction of battery cover closing. Place the clips to correct position. When the battery cover is completely closed, slide the lever to lock position.
-
Page 15: Operation Modes
For start operating with LineaPro 7 Industrial is need to be attached Apple device and installed application for iOS. For downloading the latest SDK please contact with your distributor. For turn On LineaPro 7 Industrial press one of the scan buttons and unlock Apple device screen. Scanning barcodes LineaPro 7 Industrial can scan 1D and 2D barcodes. -
Page 16: Contactless Cards Reading
USER MANUAL Contactless cards reading The LineaPro 7 Industrial has a contactless card reader. Contactless card reader is located on the bottom side. Contactless card, tag or etc… must be placed over the RF ID logo (showed on the picture below). -
Page 17: Transferring Data Between Apple Device And Pc Or Mac
- 500mA (Default) - 1000mA LineaPro 7 Industrial can charge Apple device from his own battery. Only is need to be activated function “Automated Charge”, to be start charging battery level of LineaPro 7 Industrial must be above 20%. -
Page 18: Care, Maintenance And Warranty
USER MANUAL CARE, MAINTENANCE AND WARRANTY • Keep the LineaPro 7 Industrial side of the reach of small children. • Do not drop or knock LineaPro 7 Industrial • Do not open the LineaPro 7 Industrial. Only qualified personnel can open the device and make repair.