Clas Ohlson JY-168-UK Instruction Manual

Baby Monitor
art.no. 18-2145 Model JY-168-UK
36-3923 JY-168
Please read the entire instruction manual before using the product
and save it for future reference. We reserve the right for any errors
in text or images and any necessary changes made to technical
data. If you have any questions regarding technical problems please
contact Customer Services.
Safety
• This product is not intended to substitute direct child supervision
by a responsible adult.
• Only use the type of battery recommended by the manufacturer.
• Do not place the product close to sources of heat like a heater,
cooker, candles, etc.
• Do not expose the device to moisture or immerse in liquid.
• The product is intended for indoor use only.
• This product is designed only to be used by adults for monitoring
children. Keep it out of children's reach.
Product description
Receiver
1. Belt clip
2. Channel selector
3. Aerial
3
4. Volume control
4
8 5. Power indicator
1
2
5
6. Sound level indicator
7. Adaptor connection
8. Battery cover
7
6
Transmitter
3
4
1 2
5 6
GREAT BRITAIN For consumer contact, please visit www.clasohlson.co.uk and click on customer service.
Operation
Getting Started
• Insert one 9 V battery according to the markings in the battery
compartment. N.B. To prevent leakage, remove the battery
when you don't expect to use the device for a long time.
• When using the adaptor, plug the connector into the socket (7)
on the side of the receiver. Plug the adaptor into a wall socket.
Transmitter
• The transmitter is operated by one 9 V battery.
• Place the transmitter in an appropriate location but no further
than 2 metres from the child for optimal voice reception.
• Turn on the transmitter by setting the channel selector (2) to A
or B. The red power indicator (5) should then lit.
• Make sure the same channel is set on both the receiver
and transmitter.
• The sensitivity level can be adjusted by turning the dial for
sound level control (4).
Receiver
• The receiver can be operated by one 9 V battery or the
included adaptor.
• Turn on the transmitter by setting the channel selector (2) to A
or B. The red power indicator (5) should then be lit.
• Make sure the same channel is set on both the receiver and
transmitter.
• Adjust the volume to the desired level.
• The three LEDs indicate the intensity of the sound level from the
source. The higher the sound level the more LEDs will be lit.
Care and maintenance
• Wipe the product using a soft damp cloth when necessary.
Troubleshooting
• If the transmitter is placed out of range of the receiver, inter-
ference may be heard and reception may be completely lost.
Move the devices closer to each other.
• If the transmitter is placed too close to the receiver a sharp
1. Belt clip
high-pitched sound (feedback) may be heard. Increase the
2. Channel selector
distance or decrease the volume (but not too low as to make
3. Aerial
the device ineffective).
4. Sensitivity control
• Constant background noise can mean that the batteries need to
5. Power indicator
be changed.
6. Battery cover
Disposal
Follow local ordinances when disposing of this product.
If you are unsure of how to dispose of this product, please
contact your municipality.
ENGLISH
Specifications
Channels 2
Frequency 40.695 MHz / 40.665 MHz
Power supply 1 x 9 V battery and adaptor
Declaration of Conformity
Hereby, Clas Ohlson AB, declares that following product(s):
Wireless Baby Monitor
18-2145 / 36-3923
JY-168-UK / JY-168
is in compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC.
Article 3.1a (Safety): EN 60065
Article 3.1b (EMC): EN 301489-1
EN 301489-3
Article 3.2 (Radio): EN 300220-1
EN 300220-2
0681
Insjön, Sweden, May 2009
Klas Balkow
President
Clas Ohlson, 793 85 Insjön, Sweden