Download
Share
Print this page
Timberkits Magician Assembly Instructions Manual
  1. Manuals
  2. Brands
  3. Timberkits Manuals
  4. Toy
  5. Magician
  6. Assembly instructions manual

Timberkits Magician Assembly Instructions Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
Magician

Advertisement

loading
Need help?

Need help?

Do you have a question about the Magician and is the answer not in the manual?

Questions and answers

Related Manuals for Timberkits Magician

Summary of Contents for Timberkits Magician

  • Page 1 Magician...
  • Page 2 (IT) Leggere tutte le istruzioni e guardare i diagrammi (DE) Lesen sie alle anweisungen und betrachten sie die schaubilder see this symbol. www.timberkits.com (UK) Check assembly before gluing (FR) Vérifier le montage avant collage (ESP) Controlar el montaje antes de empezar a pegar (IT) Controllare l’assemblaggio prima di incollare...
  • Page 3 Or visit our website for tips, advice and our instructional videos.
  • Page 5 41 x2 35 x2 13 x2...
  • Page 6 39 x2 3mmx14mm x4 6mmx25mm 5mmx27mm 3mmx12mm x2 21 x2 5mmx34mm 5mmx48mm 3mmx20mm x2 5mmx52mm 3mmx22mm x1 5mmx52mm 6mmx82mm 6mmx109mm 5mmx125mm 5mmx125mm 38 x8 37 x3 9 x2 40 x2...
  • Page 7 3mmx10mm 3mmx10mm 3mmx10mm 3mmx10mm Sand the top of the frame level 15mins...
  • Page 8 3mmx20mm 3mmx20mm 15mins Important: Ensure the table front is exactly vertical.
  • Page 9 3mmx16mm 5mmx48mm 5mmx125mm To ensure Parts #7 are correctly distanced apart use Cam #26 as a guide with 1mm gap between Cam and upright #7...
  • Page 10 15mins Cam Follower Assembly 3mmx14mm 6mmx109mm Sand out and wax the grooves 6mmx82mm...
  • Page 11 20mins...
  • Page 12 3mmx16mm 15mins Upper & Lower Gear Assembly...
  • Page 13 Glue #21 into place but do not get glue in centre hole or on to shaft. (See text below for detail) With a single thickness of glue shield card between the upper and the lower gear assembly and with the two shafts parallel to one another, apply glue to the long sides of #21 and slide the block along the shaft into the grove in #20.
  • Page 14 See Page 13 for gluing position of cam #26...
  • Page 15 Cams to be lined up as shown when gluing in place. Viewed from back Ensure shaft 5x34mm is protruding equally either side of #18 5mmx34mm (18) 3mmx22mm 3mmx16mm...
  • Page 16 15mins 15mins 15mins...
  • Page 17 3mmx16mm 3mmx16mm 5mmx125mm...
  • Page 18 Tilt assembly built in section 16 on its back for this stage. 15mins 10mins...
  • Page 19 Glue part #21 in place at the same height from the underside of part #4 as part #21 was glued from the bottom of part #20 earlier. (Stage 11d). Sand the surface of part 21 back level with edges of part #2 if it is proud. The 5x48mm shaft should be placed between the two 3x20mm pegs when bringing the two...
  • Page 20 5mmx52mm 5mmx52mm Assembly for left hand side when viewed from the rear of the model. 3mmx14mm Assembly for right hand side when viewed from the rear of the model. 3mmx14mm 3mmx14mm...
  • Page 21 Left table side, viewed from back. Glue part #40 to the 5mm x 52mm shaft when part #40 is exactly horizontal on the shaft as shown. Use plenty of glue and work it in.
  • Page 22 Right table side, viewed from back.
  • Page 23 3x12mm Turn assembly around 3mmx12mm...
  • Page 24 Check that shaft 6mm x 82mm is located in the hole in the table front.
  • Page 25 Turn handle until cam #26 If, after gluing, the two 5mm is pointing to the left when x 125mm shafts hit the inside viewed from the back and the of the table ends (#13), then gaps shown are at 4mm then sand of the excess until there glue block to shaft at point is a gap.
  • Page 26 6mmx25mm 10mm 30mins Spacers #37 are placed on shafts and positioned with top surface at same level as top surface of table front and glued in that position.
  • Page 27 15mins Check back edge of table top #48 is in line with back of table and that the 5mm x 52mm shafts are vertical. 15mins...
  • Page 28 30mins Note position of #43 After a few minutes before the glue is fully dry, carefully turn the handle to test the hands open evenly. Adjust if not. With the hands in the closed position, the magic object disappears as the Upper Gear moves. When the Gear Assembly is in the position shown, any one of the magic objects should be fully visible, with the edges of the centre square level with the...
  • Page 29 5x27mm...
  • Page 30 30mins Lie the model on its back and with pull rod #17 pulled down as low asit will go and with cam #22 also in lowest position (see photo) glue the two parts #58 onto the forks of part #17 above and below the cam 22 with a very slight gap.
  • Page 32 Notes...
  • Page 33 (UK) If you enjoyed building this model why not try our others. Available directly from Timberkits Ltd or from our UK, European or worldwide retail partners. Check our website to find your nearest stockist. (FR) Si vous avez apprecie construire ce modele, pourquoi ne pas en essayer d’autres. Ils sont disponibles chez Timberkits Ltd ou chez nos partenaires detaillants au Royaume Uni, en Europe et plus largement dans le monde.
  • Page 34 Timberkits Limited Old Village Hall Llanbrynmair Powys, SY19 7AA 00 (44) (0) 1650 521635 timber_kits@btconnect.com www.timberkits.com Timberkits logo and all Timberkits designs are Copyright (©) 2014 all rights reserved.