Table of Contents
Advertisement
OPERATING
FIREPLACE
Continued
OPTIONAL REMOTE
OPERATION
Note: All remote control accessories must
be purchased separately (See Accessories
on page 27). Follow instructions included
with the remote control.
Thermostat Control Operation
(Optional GHRCT Only) The thermostat
control setting on the remote control unit
can be set to any comfort level between HI
and LO. The burners will turn on and off
automatically to maintain the comfort level
you select. The ideal comfort setting will
vary by household depending upon the
amount of space to be heated, the output of
the central heating system, etc.
NOTICE: You must light the pilot
before using the hand-held re-
mote control unit. See Lighting
Instructions, page 18 .
1.
After lighting, let pilot flame burn for
about one minute. Turn control knob
on the control valve to ON position.
Turn flame adjustment knob any-
where between HI and LO. Slide the
selector switch to the REMOTE posi-
tion. Note: The burners may light if
hand-held remote ON button was on
when selector switch was last turned
off. You can now turn the burners on
and off with either optional hand-held
remote control unit.
IMPORTANT: Do not leave the se-
lector switch in the REMOTE posi-
tion when the pilot is not lit. This will
drain the battery.
IMPORTANT: Be sure to press the
ON/OFF buttons on the hand-held
remote control unit for up to 3 sec-
onds to assure proper operation.
105500
Selector Switch in Remote
Position (GHRC Optional
Remote Control)
REMOTE OFF ON
Flame Adjustment Knob
Figure 46 - Setting the (GHRC) Remote
Control Selector Switch, Valve Control
Knob, and Flame Adjustment Knob for
Remote Operation
Selector Switch in
Remote Position
(GHRCT Optional
Remote Control)
ON
OFF
REMOTE
Flame Adjustment Knob
Figure 47 - Setting the (GHRCT) Selector
Switch, control Knob, and Flame
Adjustment Knob for Remote Operation
GHRC Series Operation:
2a. Press the ON/OFF button to turn the
burners on and off. When turning
burners off, the pilot will remain lit.
GHRCT Series Operation:
2b. Select the MAN (manual) or AUTO
button on the hand-held remote con-
trol unit (see Figure 48).
• In manual mode, turn burners on
or off by pressing the ON or OFF
buttons on the hand-held remote
control unit.
Shows Temperature
Setting
Allows Burners to be
Turned On and Off
with the Hand-Held
Remote Unit
The Heater will
Automatically Cycle
Between Pilot and
the Heat Setting that
has been Selected
Figure 48 - Hand-Held Thermostat Remote Control Unit Selections
(GHRCT Only)
19
OWNER'S MANUAL
• In auto mode, the room tempera-
ture is controlled by the thermo-
Control Knob in
stat in the hand-held remote con-
On Position
trol unit. To increase the room tem-
perature, press the top arrow of the
TEMP button. To lower the room
temperature, press the bottom ar-
row of the TEMP button. At higher
settings the heater will run more.
IMPORTANT: This remote control
has been specially engineered to take
an air temperature sample every 5.5
minutes in auto mode. It will not re-
spond immediately to the tempera-
ture setting being turned up or down.
Control Knob
IMPORTANT: The hand-held remote
in On Position
control unit must be near the heater
but not extremely close to it. The
thermostat on the hand-held remote
control unit will heat up too quickly
and turn the heater off.
3.
Use the STATUS button on the hand-
held remote control unit to see the
operation mode being used and the
temperature setting selected. A red
light will come on beside the opera-
tion mode being used.
4.
To turn the burners off when operat-
ing in the manual mode, press the OFF
button. If operating in the auto mode,
press the MAN button, then press the
OFF button. The pilot will remain lit.
IMPORTANT: To turn the pilot off,
manually turn the control knob on the
heater to the OFF position.
Increases Room
Temperature
HI
Decreases Room
TEMP
Temperature
Turns Burners On
LO
MAN
ON
and Off
AUTO
OFF
Shows Current
Operation Mode
STATUS
Continued
Advertisement
Table of Contents
