1. Manuals
  2. Brands
  3. TELELYNX Manuals
  4. Media Converter
  5. Lavision-868FTA
  6. Manual

TELELYNX Lavision-868FTA Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
MODE
868FT
LAVISIO

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Lavision-868FTA and is the answer not in the manual?

Questions and answers

Related Manuals for TELELYNX Lavision-868FTA

Summary of Contents for TELELYNX Lavision-868FTA

  • Page 1 MODE 868FT LAVISIO...
  • Page 2 Make sure the AC power is unplugged in case of operator services within the device casing or close to power supply are needed. Only TELELYNX trained and approved staff is permitted to perform live line operation and maintenance within the device casing.

  • Page 3: Table Of Contents

    §2.2 System Requirements ........................8 §3 Operating the Device ............................ 9 §3.1 Quick Start ............................9 §3.2 Web Management Operation of LAVISION-868FTA ............... 9 §3.2.1 Web User Login ........................10 §3.2.2 User Management ......................... 12 §3.2.2.1 Add new user ......................13 §3.2.2.2 Edit users’...
  • Page 4 §3.2.8 Monitoring ..........................50 §3.2.8.1 Alarms ........................50 §3.2.8.2 Bitrate Monitor ......................52 §3.3 Front Panel Operation of LAVISION-868FTA ................58 Annex A: Technical Specifications of LAVISION-868FTA ................60 Annex B: Frequently Asked Questions ......................62...

  • Page 5: Introduction

    §1 Introduction §1.1 Functionality LAVISION-868FTA is a new generation ofRF-to-IP adapter, which can receive and demodulate eight channels of DVB-S/S2,DVB-C and ISDB RF input signals, and then multiplex, scramble and process it with channel coding. It adopts our newly developed functions such as “Module Management”, device scrambling, and channel modulation.

  • Page 6: Front Panel

    The ALARM LED will indicate warning messages of the device, if exists, see section §3.3 for details. Fig.1 Front Panel View of LaVision-868FTA §1.4 Rear Panel As shown in figure 2, the rear panel of LAVISION-868FTAconsists of one power supply connector, one power switch, one management port, eight RF input ports, one eight IP output ports, and a grounding point.

  • Page 7: Typical Application Architecture

    §1.5 Typical Application Architecture Fig.3 System Application Block Diagram of LAVISION-868FTA LAVISION-868FTA receives the standard DTV TS, please refer to section §3.3 for the format of TS. The following devices may be able to provide input signal to LAVISION-868FTA 1． Satellite receiving antenna and MMDS down converter.

  • Page 8: Before Use The Device

    10Gbps; the maximum data exchange speed of each port must be higher than 1000Mbps. The switch for the LAVISION-868FTA and the managing workstation should be a 100M or gigabit switch, the maximum data exchange speed of each port must be higher than 40Mbps. Normally, It can be the same switch of data output,the two ports need to be configured to different VLANs.

  • Page 9: Operating The Device

    §3.2 Web Management Operation of LAVISION-868FTA The management and control of LAVISION-868FTA can be done via a web browser. We recommend you to use Internet Explorer 6.0 or higher version, and configure the display resolution to be (or higher than)

  • Page 10: Web User Login

    §3.2.1 Web User Login After launching the Web browser, key in the IP address of LAVISION-868FTA‟s management port into the Addressbar of Web browser. Embedded Web server of LAVISION-868FTA will prompt with username and password for authentication, as shown in the figure below: Fig.4 Web Login...
  • Page 11 If you have never saved your parameters, all the parameters will change to the default state. So if you want to save your own parameters, please click in lower right corner after you finish setting LAVISION-868FTA.

  • Page 12: User Management

    §3.2.2 User Management We recommend you to change the user and password after logging by the default user and password for the safety. You can edit your user information in the user management page. Click “device setting” in the home page, and then you have the device-setting page, as shown in the figure below: Fig.8 Device setting page Click “user management”...

  • Page 13: Add New User

    In this page, you could add new user, edit old users‟ information or delete an user. Remark: Only “admin” user could enter into the user management page. §3.2.2.1 Add new user In the area of “adding user”, input correctly users‟ user name and password, and confirm password. Click “submit”...

  • Page 14: Delete An User

    In this bar, you can edit your user‟s password and that will be accomplish by clicking “submit”. Remark: You could not delete the “admin” user, but you can change the password of this user. When you use LAVISION-868FTA for the first time, you should change admin‟s password at first and then save this password.

  • Page 15: Basic Parameter Setting

    In the page of figure 11, input a right IP address in the “IP settings” bar, then click “submit” to set LAVISION-868FTA‟ network parameter. Remark: To ensure the working of device, you should guarantee that the management port IP address and LAVISION-868FTA‟ management server IP are in the same network segment...

  • Page 16: Mac Setting

    In the page of figure 11, input a right MAC address in the “MAC setting” bar, then click “submit” to set LAVISION-868FTA‟ MAC address. Remark: TELELYNX‟s products have the first 3 bytes “00:5C:B1” in the MAC address, that couldn‟t be modified.

  • Page 17: Advanced Parameter Setting

    §3.2.4 Advanced Parameter setting In the “system setting” page, click “Advanced setting” in the “select option” area To enter the parameter setting page, as shown in the figure below: Fig.13 Advanced setting page In this page, you could import/export/reset the parameters, back-up/recover the parameters, upgrade/back-up the software, import the authorization document, restart the device,etc.
  • Page 18 Fig.15 Document uploading management page System will checkout the uploading document, if its format is right, there will appear mark in the “uploading” bar and “document checkout” bar. Click “submit” button, you‟ll have this dialog box: Click “YES” button to import the parameters. Remark: Please do not turn off the device or pull the power off when the device is importing the parameters.

  • Page 19: Backup/Restore The Parameters

    As shown in the figur12, you e can choose the upgrade document in the “Software Upgrade/Export” bar, then import it to upgrade the device. Click “Browse” button, you‟ll have this dialog box: Select the upgrade document, it is a .bin file from Telelynx, click “Open” button, as shown below:...
  • Page 20 Click “Upgrade” button, system will change the page to uploading management page, as shown below: Fig.17 Document uploading management page System will checkout the uploading document, if its format is right, there will appear mark in the “Uploading” bar and “document checkout” bar. Click “Submit” button, you‟ll have this dialog box: Click “YES”...

  • Page 21: License

    1: LAVISION-868FTA has 4 types of authorization, please verify the authorization type before you buy this device. After buying this device, if you want to get a higher configuration, you can also contact with our salesman to buy the authorization.

  • Page 22: Input/Output Setting

    §3.2.5 Input/output setting Click “Input/Output” hyperlink in the navigation menu of the home page to input/output setting page of LAVISION-868FTA. The number and the name of input/output channel of the device are listed in the “Select Items” in the left side of this page, as shown below: Fig.19 Input/Output Setting...
  • Page 23 Fig.20 DVB-S/S2 settings Channel setting: in this page, the frequency parameters such as frequency, local frequency, symbol rate, polar method, 22K switch, and spectrum inversion can be set in this page of the “channel setting”. The users can judge the operation status through the last three indexes of each channel. In order to lock the signals probably, the suggested signal strength is: 42dBuV ~ 82dBuV.

  • Page 24: Ethernet Settings

    Fig.21 DVB-C settings Channel setting: in this page, the frequency parameters such as frequency, symbol rate, modulate method, work mode, and spectrum inversion can be set in this page of the “channel setting”. The users can judge the operation status through the last three indexes of each channel. In order to lock the signals probably, the suggested signal strength is: 42dBuV ~ 82dBuV.

  • Page 25: Asi Settings

    Fig.22 Ethernet settings Channel parameters:the protocol, DES address, source port, and output switch can be set in this page of the “channel settings”. Range of the parameter settings: Protocol: UDP/RTP DES address: 001.000.000.000～126.255.255.255 and 128.000.000.000～239.255.255.255 Source port: 1000~65535 Status:ON/OFF After the configuration, click “Submit” button at right-bottom of the page to save the setting. §3.2.5.3 ASI settings As shown in fig.23, click link of “ASI”, the ASI settings are shown in “channel settings”...
  • Page 26 Fig.23 ASI settings Channel parameters: the bit rate can be set in this page of the “channel settings”.

  • Page 27: Multiplexing Setting Of Programs

    §3.2.6 Multiplexing setting of Programs Click “MUX Setting” hyperlink in the navigation menu of the home page to Multiplexing setting page of LAVISION-868FTA, as shown in figure 22. Fig.24 Multiplexing setting of programs The multiplex parameter configurations are listed in the “Select Items” in the left side of this page, including the general setting, manual PID map, manual PSI inserter, NIT edit, input programs and output programs.
  • Page 28 The default of input/output character-sets, time zone and TDT/TOT can be set in this page. § § The character-sets setting and transform functions built in LAVISION-868FTA to ensure the received program information over transport stream can be displayed correctly, meanwhile ensure this information can be displayed correctly in the next device.

  • Page 29: Pid Mapping Function

    The TDT table update cycle and TOT switch can be set in the column of TDT/TOT setting. TDT update cycle(per second): update the TDT table with cyclical time. TOT switch: set it on, the device insert TOT table in the sent transport stream. After the configuration, click “Submit”...

  • Page 30: Psi Information Insertion

    As shown above, the second PID mapping has been deleted. §3.2.6.3 PSI information insertion LAVISION-868FTA support the PSI data update, i.e.: OTA file, BAT, SDT e.g.. The maximum size of the total updated file is 1024 Kbyte and the bandwidth of the updated data is smaller than 4096Kbps.
  • Page 31 Fig.28 PSI information insertion Click left- bottom “browse” and select the updating file. After select, click the “upload” bottom The system will automatically skip to the upload management page, as shown below:...
  • Page 32 The system will adjust the uploaded PSI file, if the file is uploaded correctly and the file layout is correct, the column of “upload status” and “file adjust” will display this characteristic: Click the “Submit” button below, the upload will succeed, as shown below: Fig.29 The PSI file upload successfully...

  • Page 33: Nit Edit

    The NIT of the transport stream of DTV support the information of the physical layer of the network, LAVISION-868FTA support edit NIT manually. As shown in figure 28, click “NIT edit” button, the NIT edit page is shown in the right side of the main page: Fig.30 NIT edit...
  • Page 34 FEC inner-coding, FEC outer-coding. After the configuration, click “Submit” button at right-bottom of the page to save the setting. LAVISION-868FTA support the edit of NIT Network Descriptor and NIT TS Descriptor. [Remark] the range of NIT version: 1-31...
  • Page 35 “Switch” can control the transmission of the descriptor, and click “Submit” button to save the configuration. Select the check box in any column, after that click the button in the bottom of this page, then, click “Submit”, the selected NIT network descriptor will delete. NIT TS descriptor edit: as shown in figure 31, click the corresponding “edit”...

  • Page 36: Input Program

    §3.2.6.5 Input program As shown in figure 34, click “ ” button, which at the left side of the “input program” hyperlink, the input program menu spread up, as shown below: Fig.34 Input program menu The type of the current input channel is displayed in the input program menu. As shown in figure 33, spread “channel 01”...
  • Page 37 the corresponding channel automatically, and display the information, as shown below: Fig.37 Input program information § § The information of the TS is displayed above the program list, as shown below: Fig.38 TS information Click any “ ” button at the right side of the program name, the details spread up below: Fig.39 Program TS information §...
  • Page 38 After the configuration, click “Submit” button at right-bottom of the page to save the setting. § § LAVISION-868FTA supports batch program multiplexing. It means multiplex all the programs of one channel to another selected channel. As shown below: Fig.41 Program TS information...

  • Page 39: Output Service

    click the “Submit” button, the multiplexing sets successfully as shown below: Fig.42 Batch multiplexing § § As shown in figure 40, “Keep Services When Failed”, “Default Charset” and “Analyze Timeout” are also in this page: Search overtime: when the search time is over the user setting, the search will stop. Default input character-sets: detail in 3.2.6.1.1 Switch of deletion after failure: when the search failure, switch on will delete all the information of current page.
  • Page 40 Fig.44 Output Channel List Shown as figure 44, expand the menu of „channel 01-ASI‟ to see the numbers of this channel, shown as below: Fig.45 List of Output TS Shown as figure 45, click a channel link, for example “TS002”, to enter the output TS program information page, shown as below: Fig.46 Output TS information page §...
  • Page 41 The way to edit CAT descriptor is the same as the way to edit NIT descriptor, see section 3.2.6.4.1.  SDT version, SDT sending interval  NIT sending interval  TDT/TOT sending interval  CA switch 【Remark】PAT、CAT、SDT version range：0 – 31. § § LAVISION-868FTA allows users to edit each individual program information. Click button at the front...
  • Page 42 of the program name to open the program information, shown as below: Fig.49 Program Information Editable information include program name, program number, PMT information, PCR PID, EIT information, CA related information, ES information, etc.  TS information Users can type the program name, program number, and provider in the corresponding boxes, and click “Submit”...
  • Page 43 To edit the PMT descriptors, click the “Edit”, then the “Descriptor Type” box at the bottom of the page will display Service PMT Descriptors, shown as below: The way to edit PMT descriptor is the same as the way to edit NIT descriptor, see section 3.2.6.4.1. ...
  • Page 44 Click “Submit” button to delete the program. To delete all programs, check the “Service Remove Mark Select All” box at the lower left corner, shown as below: Fig.51 Delete All Programs All programs‟ service remove mark will be automatically checked, then click “Submit” button to delete all programs.

  • Page 45: Scrambling Setting

    §3.2.7 Scrambling Setting Click “Scrambling Setting” link in the navigation bar to enter the program scrambling setting page, shown as below: Fig.52 Scrambling Setting page In “Select Items” column, there are scrambling configuration options including General Setting, CAS Configuration, and Services Scramble Setting. Fig.53 Select Items §3.2.7.1 General Setting Click “General Setting”...

  • Page 46: Cas Configuration

    “Submit” button to validate the setting. §3.2.7.2 CAS Configuration § § LAVISION-868FTA support up to 4 CAS simul-crypt, with each CA channel can be configured independently. Shown as figure 52, unfold “CAS Configuration” menu to select the CA channel 1-4:...
  • Page 47 ECMG Port (DEC): the port number of the ECM generator; 【Remark】To ensure LAVISION-868FTA can correctly receive the ECM data from the CAS, the value of ECMG IP and ECMG port on the LAVISION-868FTA must be the same as their counterparts on the CAS server.

  • Page 48: Services Scrambling Setting

    Fig.57 AC Editing Box As shown in figure 56, users can type AC information‟s name and content. After the editing, click “Submit” button to validate the settings. To delete the AC, check the square box at the end of the AC information, click “Remove”...
  • Page 49 CA descriptors will be replaced by new CA descriptor which are generated by LAVISION-868FTA. For pass-through mode, those original CA descriptors will be persisted. LAVISION-868FTA supports up to 4 CAS simul-crypt. The CAS‟s AC information is available for use only when the CAS is ON.

  • Page 50: Monitoring

    §3.2.8 Monitoring Click “Monitor” button in the navigation bar to enter the monitoring page, shown as below: Fig.61 Monitoring Page §3.2.8.1 Alarms Unfold “Alarms” menu to open the alarming information page, shown as below: Fig.62 Alarms Menu § § Click “Display” button, the alarm display page will be shown as below:...
  • Page 51 Fig.63 Alarm Information Shown as figure 63, left column displays the device temperature and the right column display alarm information. When there is no alarm, the status light will be ; when there is an alarm, the status light will turn to , and the counter will start to count the number of errors occurred, shown as below: The counter will automatically restore to zero even the error is cleared.

  • Page 52: Bitrate Monitor

    Trap: when it is ON, LAVISION-868FTA will send the trap information to server through SNMP. Panel: when it is ON, the alarm light on the front panel of LAVISION-868FTA will display the alarm. Log Level: set level of severity for the alarm, from lowest to highest level: disable, info, warning, critical.
  • Page 53 Unfold the “Input Channel” menu to enter the input channel bit rate monitoring page, shown as below: Fig.66 Input Channel Sub-menu Click the link of “channel01-Tuner” to check the bit rate of each input channel and to set the alarm information, as shown in the figure below: Fig.67 Input Channel Bit Rate Monitoring Shown as figure 67, the left column displays the real-time bit rate of each channel;...
  • Page 54 Fig.68 Sub-menu of Channel Click the “SubChannel 01” to see the PID and bit rate, as shown in the figure below: Fig.69 Sub-menu of Channel § § Unfold the “Output Channel” menu to enter the output channel bit rate monitoring page, shown as below: Click the link of „channel 01- Ethernet”...
  • Page 55 Fig.70 Output Channel Bit Rate Monitoring Shown as figure 64, the left column displays the real-time bit rate of each channel; the right column enable users to set the bit rate alarm setting, including lower limit, upper limit, and the enable switch Lower Limit: when the real-time bit rate is lower than this lower limit value, it will trigger an alarm.
  • Page 56 Fig.71 PID and Bit Rate Monitoring of Output Channel Click the link of „channel 01- ASI” to see the bit rate and to set the alarm information, as shown in the figure below: Fig.72 Bit Rate Monitoring of Output Channel Shown as figure 73, the left column displays the real-time bit rate of each channel;...
  • Page 57 Fig.73 PID and Bit Rate Monitoring of Output Channel § § Shown as figure 74, the lower right corner displays the system input, output, and insert bit rate, shown as below: Fig.74 System Bit Rate Monitoring...

  • Page 58: Front Panel Operation Of Lavision-868Fta

    § § Front panel LCD display of LAVISION-868FTA will show some initializing messages of the device at boot up stage, such as but not limited to company logo, model number, etc. If there is an error during boot up, then it will display the error message.
  • Page 59 FPGA Release Display FPGA version information. Date Set the management port IP address of The IP address should LAVISION-868FTA. be within the same Press “ENTER” key to remove cursor. Local IP subnet with Use “←” and “→” keys to switching management between different digits of the IP address.

  • Page 60: Annex A: Technical Specifications Of Lavision-868Fta

    Annex A: Technical Specifications of LAVISION-868FTA A.1 Common Technical Specifications Characteristic Properties Specifications AC Input Voltage 85～260VAC Power Supply & AC Input Frequency 50/60Hz Consumption Power Consumption 100W No. of Power Supply Modules Operating Temperature 5°C ~40°C (41°F ~104°F) Storage Temperature -25°C ~70°C (-13°F~158°F)
  • Page 61 TDT/TOT: Optional A.4 Scrambling & CAS interfaces Characteristic Properties Specification Scrambling algorithm DVB-CSA Scrambling Embedded scramblers number Table update CAT/PMT Simul-Crypt CAS number SCS interface ETSI TS 103 197 CAS Interface ECMG interface EMMG interface TCP/UDP EMM bandwidth 0~3Mbps/TS A.5 DVB-S/S2 demodulation performance Characteristic Properties Specification...

  • Page 62: Annex B: Frequently Asked Questions

    Plug in the power supply cable plugged in Check if the manage computer and the Network connect error manage port of LAVISION-868FTA has The error message “ cannot find been connected to a same network server” appears on the screen...

Table of Contents