Introduction The RichRight H.264 HD encoder is the newest HDTV product of Compunicate which adopts H.264/MPEG4 - AVC high quality compression technology. It is applied to perform DVB DTV broadcast system, MMDS, DVB data broadcast system, Video on demand system, and so on. It supports HD SDI video and audio input, HDMI video and audio input.
Products Illustration 2.1 The front panel: 1 - Indicator of Power 2 - Indicator of Keyboard Lock 3 - Indicator of Status 4 - Indicator of Network Communication 5 - LCD display 6 - Direction Key ↑ Up or Increase ↓...
2.2 The rear panel: - CVBS input port - Y input port - Pb input port - Pr input port - Audio input port (Left) - Audio input port (Right) - SDI/HD-SDI/3G-SDI input port - HDMI input port - ASI OUT A 10 -...
2.3 Installation 1、 This product should be mounted horizontally,and grouding or earthing mounted devices should be maintained reliably. 2、 Exactly connect your power supply, signal source and other equipments to this product. 3、If you want to use the Head-end Netmanager, Please connect RJ45 to your network.
Operation Menu 3.1 Menu Structure The under chart illustrates the device menu tree. You can browse and operate all of the parameters via keyboard of the front panel. Note: Enc2-Enc4 Setting and IP2-IP4 Setting are optional.
Page 10
Video Input PMT PID 1-12 Video Resolution PCR PID 1-13 Video Bit Mode Enc1 Setting VID PID 1-14 Video BitRate AUD PID 1-15 Enc2 Setting Max BitRate(VBR) Service ID 1-16 Enc3 Setting Min BitRate(VBR) TS ID 1-17 Enc4 Setting GOP Structure Packet Size 1-18 Audio Input...
3.2 Menu Definition 3.2.1 Enc1 Setting “Video Input 1-1” : User can choose the video input port. There are 4 types of input ports: CVBS, SDI, YPbPr and HDMI. Note: For Enc2-4, there are only 2 types of input ports: SDI and HDMI. “Video Resolution 1-2”...
range is from 50 to 8190. “AUD PID 1-15” : User can configure the output audio PID. The range is from 50 to 8190. “Service ID 1-16” : User can configure the output service id. The range is from 1 to 65535. “TS ID 1-17”...
“TS ID 5-4” : User can configure the Transport Stream ID. The range is from 1 to 65535. Note: For single channel encoder, there is no this menu. 3.2.6 IP1 Setting “Source 6-1” : User can select the output source. There are 6 types of souce: none, enc1, enc2, enc3, enc4 and mux.
3.2.9 IP4 Setting (Optional) The menu is similar to IP1 Setting. 3.2.10 IP5 Setting (Optional) The menu is similar to IP1 Setting. 3.2.11 Host IP Setting “Host IP 11-1” : The host IP Address setting. “Host Netmask 11-2” : Subnet Mask setting. “Host Gateway 11-3”...
Gateway 192.168.1.1/192.168.0.1 Device 192.168.1.100 Server 192.168.0.10 3.2.12 Advanced Setting “Save Defualt 12-1” : Save the current configuration as default configuration. “Load Default 12-2” : Recall the default configuration whitch has been saved. “Restore initial 12-3” : Recall the original configuration whitch was configured by manufactory.
Operation 4.1 Operation via keyboard Turn on the power switch after checking the system connections. The following information will be displayed on screen: Model name & V2.10 SN:114122100999 The SN is the unique serial number of this product. The following chart displays the definition of SN.
4.2 Operation via Web Manager Type the encoder’s host IP address, the main frame will be showed in IE. 4.2.1 System Information There is some basic system information in main frame, showed as Figure.
4.2.2 System Setting System parameters include output system bitrate, packet length, basic PIDs, service name, service provider name, TS ID and service ID. Service name and service provider name support up to 40 characters. 4.2.3 Video Setting Video parameters include input port, resolution info, encode mode, GOP structure, and average bitrate.
4.2.4 Audio Setting Audio parameters include input port, bitrate, audio encode format, audio bitrate and audio gain. There are 3 types audio input ports: Analog, HDMI and Embedded SDI. Audio encode format only supports MPEG-1 Layer II and AC-3 pass-thru. For AAC version, it also supports AAC-LS...
4.2.5 TS IP Setting This setting is only for TS IP output port. Stream IP: Local IP Address. There are 2 types protocol: UDP and RTP. Destination IP & Port: Destination IP address and IP port. IGMP: The default parameter is Disable. 4.2.6 Host IP Setting This setting is only for manager port.
Technical specification 5.1 Surrounding specification Surrounding specification Temperature Range Working Temperature 0℃~45℃ Storing Temperature -20℃~70℃ Power Supply 100~240VAC,47~63Hz Power <30W 5.2 Mechanical standard Mechanical standard Height 44mm(IRU) Width 482mm Depth 330mm Weight About 3.5kg 5.3 Input interface Input interface Channel 1 Video CVBS, YPbPr, SDI/HD-SDI/3G-SDI, HDMI Audio...
Need help?
Do you have a question about the IDH-9001 and is the answer not in the manual?
Questions and answers