Page 2
MANUAL which is supplied with the truck. The OWNERS MANUAL can also be found in the downloads section on the ecovolve website, www.ecovolve.eu. The OWNERS MANUAL contains more detailed and complete information on the operation, maintenance, transport, servicing and technical data for the ED1000. Manufacturer : Ecovolve Model : ED1000 : .
Safety Safety regulations Always follow the warnings contained within this operators handbook and on the ED1000 to avoid incidents and accidents from occuring unnecessarily. The following symbols and the signal words DANGER, WARNING, CAUTION and ELECTRICAL WARNING indicate hazards and instructions.
Safety Decal warning symbols Warning! Read and understand the instructions in the manual before operating the truck. Indicates a right or left hand turn with the use of hand signals. 10° max Danger! Do not drive the truck with the skip in the raised position.
Overview Operators platform and safety rails CAUTION The following section is an overview of the operators platform and safety rails. All operators must read and fully understand the instructions before operating the truck. Operators platform The truck has a 2 position platform for the operator to stand on when operating the machine. In the raised position the operator can walk behind the truck (fig 1).
Overview Dashboard controls CAUTION The following section is an overview of the dashboard controls. All operators must read and fully understand the instructions before operating the truck. FIG 1 FIG 3 FIG 2 Multi function display. Key ignition switch Emergency stop button. Battery discharge and fault codes indicator.
Overview Tiller head controls CAUTION The following section is an overview of the tiller head controls. All operators must read and fully understand the instructions before operating the truck. FIG 1 FIG 2 FIG 3 Flashing Beacon & Horn Switch: Pressed IN Speed Switch.
Operation Operating the truck Switching on the truck • Ensure the tiller head is in the central position and disengage the emergency stop button. • Insert the key into the key switch and turn clockwise from the zero position to position “II” and hold for 3 seconds. The traction wheel will reset and the multi function display unit will display the battery discharge status.
Page 10
Operation Operating the hi tip skip functions The truck is equipped with a high tip function. The skip lever is located on the dashboard which operates all the functions of the skip. The skip lever functions in four positions: Tilting the skip FORWARD: Push the lever to the RIGHT. �...
Operation Parking In the interest of safety, It is the operators responsibility to ensure that the truck is parked in a safe and secure manner. When parking the truck: • The start key must be turned anticlockwise to “0” to turn off the truck. •...
Charging Charging the battery The battery charging port is located at the rear of the truck above the operators platform (fig 1). � The dumper is supplied with a 3m charging cable. Ensure the truck is parked safe and securely, remove the key and activate the emergency stop �...
Transportation Transporting the truck The Ecovolve ED1000 is easily transportable. It is comparatively lightweight for its capacity and can be loaded on to a vehicle with a load rating of 1300 kg minimum. The operator’s platform can be raised up and the safety rails can be lowered down for ease of transportation.
Page 15
Transportation Lifting and anchor points The truck is equipped with two lifting eyes and five anchor points which are used in conjunction � with straps or chains to lift and also to secure the machine to the transport vehicle. Use certified slings and chains to lift and secure the truck during transport. �...
100-240 ed Charging - Input (V AC) 50.0 A 50.0 A 100.0 A - Output (V DC) Technical data e (Hrs) Induc tion moto r ED1000 Metric key measurements 5KW/7HP 5KW/7HP 5+4KW/11HP and ground pressure Zero Zero Zero 60-80 60-80...
100-240 100-240 ed Charging - Input (V AC) 50.0 A 50.0 A 100.0 A - Output (V DC) Technical data e (Hrs) Induction moto r ED1000 Imperial key measurements and ground 5KW/7HP 5KW/7HP 5+4KW/11HP pressure Zero Zero Zero 60-80 60-80...
NOTE: Please refer to the servicing section (5) in the owner’s manual for information on the specified torque settings on the front and rear wheel retaining nuts. The owners manual can be found in the downloads section on the Ecovolve website - www.ecovovle.eu.
Need help?
Do you have a question about the ED1000 and is the answer not in the manual?
Questions and answers