Thoroughly inspect the unit for shipping damage with particular attention to connectors and controls. If there is any sign of damage to the unit or damaged or loose connectors contact your distributor right away. NACE: 610-429-1511 | sales@datatronix.biz | www.datatronix.biz | | DT-ATSC-IP-8 Manual v1.0 Page 3...
IP. The outputs can be mapped to a desired unicast or multicast IP address. The DT-ATSC-IP-8 unit will also process most major local networks broadcast that have a second or third local channel which can contain important weather related content, local sports, and secondary programming.
Dimensions W x D x H (Excluding Connectors) Weight lbs./kg 8 lbs 13.01 oz, 4 kg *Subject to change without notifications *Manufactured under License of Dolby Laboratories NACE: 610-429-1511 | sales@datatronix.biz | www.datatronix.biz | | DT-ATSC-IP-8 Manual v1.0 Page 5...
Be sure the connections for each source are consistent with the unit’s inputs (Input 1…Input 8). 3. Connect an ethernet cable from IP OUT Port on the destination. 4. Connect an ethernet cable from UTILITY Port on the DT-ATSC-IP-8 to a PC/MAC for setting. 5. Connect the included power cord to the unit’s POWER plug.
◊ Save all changes as required, upload and reboot changes. ◊ Verify parameters then end web session. Overview Page Overview Page will provide an overall system status of the DT-ATSC-IP-8 Converter state: Signal Strength and Signal Quality. System Parsing / Response Time: The initial System Parsing time will range from 3-4 minutes on average as the system identifies and populates the required parameters.
Move the cursor to the “Select Columns” icon and press the icon to set. After selecting the columns, press the “Apply” button at the bottom to apply the changes. NACE: 610-429-1511 | sales@datatronix.biz | www.datatronix.biz | | DT-ATSC-IP-8 Manual v1.0 Page 9...
4. For Static IP: Select Static IP and enter Static IP address for device. (record New IP address). 5. Enter Subnet Mask. 6. Enter Default Gateway. 7. Save and Confirm all changes. NACE: 610-429-1511 | sales@datatronix.biz | www.datatronix.biz | | DT-ATSC-IP-8 Manual v1.0 Page 10...
Reboot Use the Reboot command button to reboot the device. Reset to Default Use the Reset to Default button to reset all parameters to original factory settings. NACE: 610-429-1511 | sales@datatronix.biz | www.datatronix.biz | | DT-ATSC-IP-8 Manual v1.0 Page 11...
Select “Upload image” to import the selected file into the device. Note: backup can be imported to assist in setting up new or multiple devices onsite. Remember to save and backup any and all changes. NACE: 610-429-1511 | sales@datatronix.biz | www.datatronix.biz | | DT-ATSC-IP-8 Manual v1.0 Page 12...
Change Password Use the Change Password section to change or modify the device’s password as desired. NACE: 610-429-1511 | sales@datatronix.biz | www.datatronix.biz | | DT-ATSC-IP-8 Manual v1.0 Page 13...
1. A complete and accurate site survey must be completed by a Satellite System Integrator prior to the purchase or installation of any satellite reception hardware. 2. A complete and accurate list of desired satellite orbit spots and transponders must be obtained. NACE: 610-429-1511 | sales@datatronix.biz | www.datatronix.biz | | DT-ATSC-IP-8 Manual v1.0 Page 15...