Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for RSI Systems Furniture EZcube
Summary of Contents for RSI Systems Furniture EZcube
- Page 1 EZcube Installation Guide RSI Systems Furniture...
- Page 2 EZcube Installation Guide Panels Connection Posts Top Cap / End Trim Worksurface Brackets Support Leg Shelf Power Blocks / Connectors Infeeds RSI Systems Furniture...
- Page 3 EZcube Installation Guide Connector-B Connector-A (Threaded Connector) (Non-Threaded Connector X3 Panel Connection STEP 1: Lift up and remove the fabric tile from one side of the panel. STEP 2: Determine which side of the panel has Connector-A and Connector-B STEP 3: Grab your X3 panel screw, stick it through Connector-A and start screw- ing it into Connector-B.
- Page 4 EZcube Installation Guide Figure: 6.1 Figure: 6.2 Figure: 6.3 X1 Panel Connection STEP 1: Determine which side the brackets are on. See Figure 6.3 STEP 1: Lift up the panel you are connecting and lower in on to the interlocking brackets of the panel you are connecting to See Figure 6.1...
- Page 5 EZcube Installation Guide Connector-A (Non-Threaded Connector Figure: 7.1 Figure: 7.2 X3 Panel to X31 Post Connection STEP 1: Fit the X31 Post centering pieces (See Figure 7.1) into the X3 Panel Rail. STEP 2: Feed your X31 Post Screw through the Connector-A bracket and in to the post.
- Page 6 EZcube Installation Guide X3 Panel to X3 Post Connection STEP 1: Fit the X3 Post centering pieces into the X3 Panel Rail. STEP 2: Feed your X3 Ponel Screw through the Connector-A bracket and into the post. NOTE: If you have Connector-B mounted inside the panel you will need to swap them out with the extra Connector-A brackets that are included in your hardware pack.
- Page 7 EZcube Installation Guide X3 Top Cap STEP 1: Snap the top cap down at an an- gle to get it started. STEP 2: Make sure that the top cap is completely seated against the top of panel. X3 End Trim...
- Page 8 EZcube Installation Guide X1 End Trim STEP 1: Remove the X1 Panel Side Top cap (See Figure 10.1-10.2) STEP 2: Unscrew the X1 connecting brackets and slide up and off the panel STEP 3: Put the X1 Panel Side Top Cap back on the panel STEP 4: Insert L-Shaped end first then snap into place Figure: 10.1...
- Page 9 EZcube Installation Guide Figure: 11.1 Figure: 11.2 Figure: 11.3 X3 Worksurface Brackets STEP 1: Angle the work surface bracket and insert the top tooth into the Side Rail (See Figure (11.1-11.3) STEP 2: Make sure the bracket is completely seated on the side rail Figure: 11.4...
- Page 10 EZcube Installation Guide Front Edge Worksurface Leg Install STEP 1: Position the leg so it is flush with the front corner edge of the surface. STEP 2: Attach one screw to the bottom side of the surface. This will provide additional support while you attach the surface to the corner bracket that will be positioned behind the leg.
- Page 11 EZcube Installation Guide Figure: 13.1 Figure: 13.2 X3 Shelf STEP 1: Install the shelf ends to the bottom shelf pan with the screws provided. STEP 2: Angle the shelf and insert the top tooth into the side rail. STEP 3: Make sure the bracket is completely seated on the side rail Figure: 13.3...
Need help?
Do you have a question about the EZcube and is the answer not in the manual?
Questions and answers