Advertisement
Info: The most current version of these instructions can be found online at
Tools required:
3
/
" hex key,
16
IMPORTANT SAFETY INFORMATION: PLEASE READ
WARNING: Important! Read and understand these instructions before assembling or
using the LF1009A Lift Scale Kit. If you do not understand any part of these warnings,
cautions or instructions, contact a healthcare professional for direction in the use of
this product. If the Lift Scale Kit is not properly assembled and installed, personal
injury and damage to the Lift Scale Kit could result.
WARNING: If components are damaged or missing, contact your Graham-Field
authorized distributor immediately. DO NOT use substitute parts. Use only Lumex
replacement parts. Non-Lumex replacement parts could cause personal injury and
damage to the LF1009A Lift Scale Kit.
WARNING: This product has a maximum weight capacity of 600 lb (272 kg). The
lift, however, may have a lower maximum weight capacity; do not exceed your lift's
maximum weight capacity when using this scale.
WARNING: Notice for California Customers- California Proposition 65 WARNING: This
product contains a chemical known to the State of California to cause cancer and
reproductive or developmental harm.
WARNING: GF Health Products, Inc. assumes no responsibility for any damage or injury
caused by improper assembly, installation or use of this product.
INTENDED USE
The LF1009A Lift Scale Kit is intended to weigh patients (in pounds or kilograms) during lifts.
ASSEMBLY
1. See picture at right. Remove black cap from spreader
bar pivot pin.
2. Position upper scale between lift boom mounting
brackets with scale display facing outward. Insert long
shoulder bolt through lift boom mounting brackets,
black spacers, and upper scale as shown. Install lock
nut on shoulder bolt. Use
to tighten.
Info: Each mounting link has a recess where the short
shoulder bolt's head should mount. If shoulder bolts are
not mounted in these recesses, they will be too short.
3. Insert upper short shoulder bolt through mounting links
and lower scale as shown. Install lock nut on shoulder
bolt. Use
3
/
" hex key and
16
4. Place white spacer over end of pivot pin. Insert pivot
pin upward through center of spreader bar as shown.
5. Insert lower short shoulder bolt through mounting
links, white spacers, and pivot pin as shown. Install
lock nut on shoulder bolt. Use
wrench to tighten.
6. Discard remaining hardware.
LF1009A-INS-LAB-RevB14
LF1009A: LIFT SCALE KIT
ASSEMBLY & OPERATION INSTRUCTIONS
PLEASE SAVE THESE INSTRUCTIONS FOR FUTURE USE
1
/
" wrench
2
3
/
" hex key and
1
/
16
2
1
/
" wrench to tighten.
2
3
/
" hex key and
16
lock nut
black spacer
upper short
shoulder bolt
" wrench
lock nut
mounting link
white spacer
spreader bar
black cap
white spacer
1
/
"
2
www.grahamfield.com.
lift boom
pivot pin
LF1009A Lift Scale Assembly
black spacer
long
shoulder bolt
scale
white spacer
mounting link
lock nut
recess
lower short
shoulder bolt
1
Advertisement
Table of Contents
Related Manuals for Lumex LF1009A
Summary of Contents for Lumex LF1009A
- Page 1 IMPORTANT SAFETY INFORMATION: PLEASE READ WARNING: Important! Read and understand these instructions before assembling or using the LF1009A Lift Scale Kit. If you do not understand any part of these warnings, cautions or instructions, contact a healthcare professional for direction in the use of this product.
- Page 2 GF instructions. Product provided to users as rentals must be serviced by the provider and inspected prior to delivery. Each user must be properly trained on the operation and safety of this product prior to use. Within the guidelines set forth in this document, the Lumex LF1009A Lift Scale is warranted for one (1) year.
Need help?
Do you have a question about the LF1009A and is the answer not in the manual?
Questions and answers