Important Safety Instructions - Honeywell BH-888E User Instructions

IMPORTANT SAFETY INSTRUCTIONS

Read through all the instructions before starting to use the
fan heater. Keep this instruction manual in a safe place for
future reference.
1. Supervision is necessary when the fan heater is used in
the vicinity of children.
2. Do not use the fan heater outdoors.
3. The fan heater must only be used after it has been moun-
ted according to this instruction manual. Mount the fan hea-
ter vertically on a straight wall: Be sure to observe the speci-
fied safety distances as shown in Fig. 1 and 2, and also
observe your local safety regulations. Do not mount the fan
heater on combustible or instable surfaces (e.g. wood or
plastic surfaces) or under the ceiling. Fire hazard!
4. Unwind the power cord completely. An incompletely
unwound power cord can lead to overheating and cause a
fire. Do not touch the power cord with wet hands. Make
sure that there are no objects are resting on the power
cord or could come into contact with hot parts. Position
the power cord where nobody can trip over it and where
the power socket is easily accessible.
5. Do not use an extension cord, a multiway connector or
an infinitely variable speed controller. These can lead to
overheating, fire or electric shock.
6. Connect the fan heater only to a single-phase socket
with the supply voltage as stated on the type plate of the
appliance. The fan heater is equipped with double electric
insulation (Class II) and does not have to be earthed.*
7. Always switch the fan heater off with the rotary thermo-
stat switch (2) and always disconnect the power plug (8)
from the power socket when the fan heater is not in use.
Allow the fan heater to cool off for at least 20 minutes
before it is moved, handled or cleaned. Do not tug at the
power cord to disconnect the plug. Handle the fan heater
only with dry hands. Do not leave the fan heater unatten-
ded when it is running.*
8. Do not use the fan heater anywhere near inflammable
gases or substances such as solvents, lacquers, glues etc.
9. Do not mount the fan heater immediately under a power
socket.
10. Do not mount and use the fan heater in close proxi-
mity to a bathtub, a shower or a swimming-pool (Fig. 1).
11. Do not use the fan heater in any kind of vehicle (e.g.
portacabin, lift, elevator, motor vehicle, cubicle) or similar
enclosed space.
12. Caution: The air outlet vent (7) of the fan heater gets
very hot during use. Inflammable materials such as cus-
hions, pillows, duvets, blankets, furniture, paper, curtains,
drapes and clothing must be kept at least 100 cm distance
from the fan heater (Fig. 2).
13. Keep the fan heater clean. Make sure that the air intake
vent (6) and air outlet vent (7) are open before starting to
use the fan heater. Do not allow objects to get into the air
intake vent (6) or air outlet vent (7). Do not cover up the
fan heater (( ) symbol on the side of the fan heater) This
can lead to overheating, fire or electric shock.
14. Do not dip the fan heater in water or any other liquids
and do not pour water or any other liquids over the appli-
ance or into the air intake vent (6) or air outlet vent (7).
15. The fan heater is equipped with protection against
water, Grade IPX4. This facilitates use in a bathroom or a
damp environment. However, installation inside a bath or
shower cell is not possible. The safety distances shown in
Fig. 1 must be strictly observed. The rotary switch must
not be accessible to persons using the bathtub or shower.
16. Clean the fan heater regularly by following the cleaning
instructions.
17. The fan heater must only be used according to the
instructions in this instruction manual. Non-observance of
these instructions can result in injuries, fire, electric shock
or defects in the appliance.
18. The fan heater is intended exclusively for private use
indoors. It is not suitable for commercial use.
19. If the power cable of the fan heater is damaged it must
be replaced by the manufacturer or by a repair shop
approved by the manufacturer, or by similarly qualified
persons, so as to avoid damage.
20. Do not use this fan heater if it is damaged or shows
signs of damage, or if it has fallen down or is not functioning
correctly. Disconnect the power plug from the power socket.
CONSTRUCTION
1. Power control lamp
2. Rotary thermostat switch
3. Room temperature approx. + 5 °C ( )
4. Room temperature approx. + 30 °C
5. 60 minute timer
6. Air intake vent
7. Air outlet vent
8. Power cord with power plug*
9. Wall bracket indents
10. Rear wall bracket
11. Air filter
5
ENGLISH