Mighty Mule VEHICLE SENSOR Installation Manual page 10

For Installation on Other Brand Gate Openers ... For Installation on Other Brand Gate Openers ...
I you are using the I you are using the
VEHICLE SENSOR VEHICLE SENSOR
tion below or wiring the system. I you do not understand the instructions below, please call GTO's tion below or wiring the system. I you do not understand the instructions below, please call GTO's
Technical Support at 1-800-543-1236. Technical Support at 1-800-543-1236.
T T ypical Gate ypical Gate Wiring Connection: Wiring Connection:
• • Reerence Leads: Reerence Leads:
RED RED => => Input Input V V oltage
o o
SHIELD SHIELD => => Ground/Common Ground/Common (–)
o o
BLACK BLACK => Relay's => Relay's Common
o o
BLUE BLUE => => Relay' Relay's s Normally
o o
YELLOW YELLOW => => Remote Remote SENSOR
o o
Terminology Defnitions: Terminology Defnitions:
• •
'FREE EXIT/ENTRY' is dened as input terminals (2) that upon activation (momentarily connected together) will 'FREE EXIT/ENTRY' is dened as input terminals (2)
o o
cause the gate to run in the open direction only. Note: In most cause the gate to run
MON/GND'. MON/GND'.
• • Power supply connection: Power supply connection:
DC power supply: (11-36 Vdc) DC power supply: (11-36 Vdc)
o o
Connect the positive (+) lead o the power supply to the RED wire. Connect the positive (+) lead o the power supply to
ß ß
Connect the negative (-) lead o the power supply to the SHIELD wire. Connect the negative (-) lead o the power supply to
ß ß
AC power supply: (8-26 Vac) AC power supply: (8-26 Vac)
o o
Connect the power supply to the RED & SHIELD Connect the power supply to the
ß ß
• • Relay output connection: Relay output connection:
Connect the BLUE w ire rom the SENSOR Connect the BLUE w
o o
Connect the BLACK wire rom the Connect the BLACK wire rom the SENSOR to the
o o
• • Range (POT) board connection: Range (POT) board connection:
Connect the YELLOW wire rom the SEN Connect the YELLOW wire rom the SEN SOR to
o o
Connect the BLACK wire rom the Connect the BLACK wire rom the Range Adjustment Board to a negative input voltage.
o o
Turn the POT clockwise to increase range. Turn the POT clockwise to increase range.
o o
Turn the POT counter-clockwise to decrease range. Turn the POT counter-clockwise to decrease range.
o o
Generic Wiring Diagram Generic Wiring Diagram
on any other automatic gate opener brand, use the inorma- on any other automatic gate opener brand, use the inorma-
oltage (+) (+)
(–)
Common
Normally Open Open
SENSOR [Range [Range adjustment adjustment potentiometer
in the open direction only. Note: In most gate openers, one o the
RED & SHIELD wires. There is no polarity or AC power supply.
ire rom the SENSOR to the 'FREE EX to the 'FREE EX IT/ENTR
SENSOR to the 'COMMON/GND' o the gate opener
SOR to the YELLO
Range Adjustment Board to a negative input voltage.
RED RED
Input Input
Voltage (+) Voltag e (+)
SHIELD SHIELD
Input Input
Voltage (–) Voltag e (–)
BLACK BLACK
Relay Output Relay Output
Common Common
BLUE BLUE
Relay Output Relay Output
Normally Open Normally Open
YELLOW YELLOW
Range Range
Adjustment Adjustment
SENSOR SENSOR
potentiometer (POT)] (POT)]
that upon activation (momentarily connected together) will
gate openers, one o the two terminals is the 'COM-
the RED wire.
the SHIELD wire.
wires. There is no polarity or AC power supply.
IT/ENTRY' o the gate opener. Y' o the gate opener.
'COMMON/GND' o the gate opener. .
the YELLOW wire rom W wire rom the Range Adjustment Board. the Range Adjustment Board.
W W
O O
L L
L L
E E
Y Y
7 7
two terminals is the 'COM-
Input Voltage Input Voltage
11 - 36 Vdc or 11 - 36 Vdc or
8 - 26 Vac 8 - 26 Vac
+ +
– –
Free Exit/Entry Free Exit/Entry
Connections Connections
K K
C C
A A
L L
B B
Range Range
Adjustment Adjustment
Board Board