Related Manuals for BETCO FiberCAP 15
Summary of Contents for BETCO FiberCAP 15
- Page 1 E29974 FiberCAP 15” Carpet ™ Cleaning Machine Operator Manual 400 Van Camp • Bowling Green, Ohio 43402 Customer Service: 888-GO-BETCO • Fax: 800-445-5056 • Technical Service: 877-856-5954 • www.betco.com...
-
Page 2: Table Of Contents
TABLE OF CONTENTS RECEIVING THE MACHINE....................2 TECHNICAL SPECIFICATIONS ..................... 2 GENERAL SAFETY REGULATIONS ..................3 MACHINE PREPARATION ....................4 - 6 USE AND MAINTENANCE TIPS ................... 7 PARTS DIAGRAMS AND LISTINGS ................8 - 11 WARRANTY ........................12 RECEIVING THE MACHINE Immediately check, when receiving the machine, that all the materials indicated on delivery documents have been received and also that the machine has not been damaged in transit. -
Page 3: General Safety Regulations
• Before using the machine make sure that all doors and covers are positioned as shown in this operating and maintenance manual. • When your BETCO machine is ready to be retired, the machine must be disposed of properly. It contain oils and electronic components. The machine was built using totally recyclable materials. -
Page 4: Machine Preparation
MACHINE PREPARATION 1. ASSEMBLING THE HANDLE The handle assembly is comprised of four individual parts. A. Install the main cross bar onto the machine by pulling the finger pins outward on both sides and locking them into the handle mounts of the machine. - Page 5 MACHINE OPERATION 1. STARTING THE MACHINE A. Attach the extension cord to the plug on the machine. B. Insert cord through strain relief holder. C. Plug into a grounded 110V/120V outlet. D. Push down the start lever on the left side of the machine. The machine will automatically start when the handle is lowered to an operating position.
- Page 6 Follow these steps for interim encapsulation cleaning of carpet: A. Start by removing large and loose debris. This can be done by installing the optional dust collection bins or with a vacuum. B. In a spray bottle or pump sprayer dilute the Betco FiberCAP™ MP ®...
-
Page 7: Use And Maintenance Tips
B. Should this happen, disconnect the power supply, wait 30 seconds, and press the button inwards to reset the safety switch. C. Then reconnect the power supply and continue working. D. If the safety switch continually trips, cease operation and please contact your Authorized Betco Distributor or Retailer. -
Page 8: Parts Diagrams And Listings
MACHINE DIAGRAM PARTS LISTING... - Page 9 MACHINE DIAGRAM PARTS LISTING Item# Part# Description Item# Part# Description E13190 Spacer, Motor E84627 Washer, Lock, M5 E13191 Motor, 1.0 HP E84629 Grommet E13192 Spacer, Motor E84630 Screw, M4 x 12 E13194 Stud, Motor E84631 Gear, 66, Right E84632 Circuit Breaker E13195 Cover, Brush E84635...
- Page 10 HANDLE DIAGRAM PARTS LISTING Item# Part# Description Item# Part# Description E13200 Handle Bar, Upper Section E84670 Handle Tube, Lower Left E13201 Handle Base Cross Bar E84671 Handle Tube, Lower Right E13214 Handle Complete E84677 Hook, Cord Wrap ACCESSORIES DIAGRAM PARTS LISTING Item# Part# Description Item# Part#...
- Page 11 BRUSH OPTIONS Part Appearance Number Description ELECTRICAL WIRING DIAGRAM Electronic Switch Micro 2 (Relay) Run Cap 2-5 Protector Micro 1 Motor Grounds 2-3-5 Cover Plug Start Cap 1-5...
-
Page 12: Warranty
Service Distributor. If the original part is returned within the warranty policy period from date of delivery for inspection by Betco and is found to be defective the owner will be credited for the cost of replacement parts plus shipping and handling.
Need help?
Do you have a question about the FiberCAP 15 and is the answer not in the manual?
Questions and answers