Subscribe to Our Youtube Channel
Related Manuals for Dynaset 60
Summary of Contents for Dynaset 60
- Page 1 INSTALLATION GUIDE HYDRAULIC VARIABLE DISPLACEMENT PUMP 60 cm 90 cm 110 cm Download PDF version from www.Dynaset.com/manuals Keycode: X3CP8K...
-
Page 2: Table Of Contents
TECHNICAL SPECIFICATIONS INSTALLATION MEASUREMENTS INSTALLATION ..5.1. ADJUSTING LS-PRESSURE MAINTENANCE ..6.1. MAINTENANCE INTERVAL MANUFACTURERS LIMITED WARRANTY PRODUCT DISPOSAL DECLARATION OF CONFORMITY Dynaset Oy | Menotie 3, FI-33470 Ylöjärvi, Finland | tel: +358 3 3488 200 | info@dynaset.com | www.dynaset.com... -
Page 3: General
The LS-0 block is installed between hydraulic pump and the pump controller. It is available for both 12V and 24V systems by request. Dynaset Oy | Menotie 3, FI-33470 Ylöjärvi, Finland | tel: +358 3 3488 200 | info@dynaset.com | www.dynaset.com... -
Page 4: Safety
This is to ensure safe, reliable and longlife operation of your equipment. When working with DYNASET products or their accessories, wear appropriate protective clothing, safety goggles, gloves, ear protection. Dynaset Oy | Menotie 3, FI-33470 Ylöjärvi, Finland | tel: +358 3 3488 200 | info@dynaset.com | www.dynaset.com... -
Page 5: Technical Specifications
*Different flange size options available depending on the required flow rate. 38mm(1 1/2"), 42 mm, 50mm(2"), 64mm(2 1/2"), 76mm(3"). ** Without the Suction flange. Dynaset Oy | Menotie 3, FI-33470 Ylöjärvi, Finland | tel: +358 3 3488 200 | info@dynaset.com | www.dynaset.com... -
Page 6: Installation Measurements
Different flange size options available depending on the required flow rate. Measurements may vary if pump is equipped with additional options, suchs as valves or different flanges. Dynaset Oy | Menotie 3, FI-33470 Ylöjärvi, Finland | tel: +358 3 3488 200 | info@dynaset.com | www.dynaset.com... - Page 7 G 1/4 Connected *Different flange size options available depending on the required flow rate. 38mm(1 1/2"), 42 mm, 50mm(2"), 64mm(2 1/2"), 76(3"). Dynaset Oy | Menotie 3, FI-33470 Ylöjärvi, Finland | tel: +358 3 3488 200 | info@dynaset.com | www.dynaset.com...
-
Page 8: Installation
Install the pump through following steps: 1. Ensure the rotation direction. R =clockwise, L = counter-clockwise. 2. Fill the hydraulic pump's casing with filtered oil Dynaset Oy | Menotie 3, FI-33470 Ylöjärvi, Finland | tel: +358 3 3488 200 | info@dynaset.com | www.dynaset.com... - Page 9 10 min at pressure being under 50 bar. Bleeding/flushing the system is recommended before the full pressure range is used. Dynaset Oy | Menotie 3, FI-33470 Ylöjärvi, Finland | tel: +358 3 3488 200 | info@dynaset.com | www.dynaset.com...
-
Page 10: Adjusting Ls-Pressure
2. Start the engine of your base machine and set it up to the required RPM level needed for yout hydraulic system to operate. Start the hydraulic system. Dynaset Oy | Menotie 3, FI-33470 Ylöjärvi, Finland | tel: +358 3 3488 200 | info@dynaset.com | www.dynaset.com... -
Page 11: Maintenance Interval
Hydraulic Oil Filter Change Hydraulic Oil Change (check and clean the oil level gauge) x* Only for a new device after first 100h. Dynaset Oy | Menotie 3, FI-33470 Ylöjärvi, Finland | tel: +358 3 3488 200 | info@dynaset.com | www.dynaset.com... -
Page 12: Manufacturers Limited Warranty
DYNASET OY or to other location authored by DYNASET OY. Shipment documents must contain: Purchaser’s name and contact information Receipt of original purchase WRN code Problem description Dynaset Oy | Menotie 3, FI-33470 Ylöjärvi, Finland | tel: +358 3 3488 200 | info@dynaset.com | www.dynaset.com... - Page 13 • Product that is used in exceptional conditions, considered to cause excessive wear and tear. • Faults caused by nature phenomenon’s like flood, thunder, etc. © DYNASET OY, all rights reserved Dynaset Oy | Menotie 3, FI-33470 Ylöjärvi, Finland | tel: +358 3 3488 200 | info@dynaset.com | www.dynaset.com...
-
Page 14: Product Disposal
NOTE! Always act according to the waste legislation, regulations and recommendations in waste disposal and waste recycling issued by your local authorities. Dynaset Oy | Menotie 3, FI-33470 Ylöjärvi, Finland | tel: +358 3 3488 200 | info@dynaset.com | www.dynaset.com... -
Page 15: Declaration Of Conformity
If the device has been modified by someone other than the manufacturer or without the manufacturer’s permission, this declaration is not valid. Timo Nieminen R&D Manager Ylöjärvi, Suomi, 20.04.2016 Dynaset Oy | Menotie 3, FI-33470 Ylöjärvi, Finland | tel: +358 3 3488 200 | info@dynaset.com | www.dynaset.com... - Page 16 Menotie 3 33470 Ylöjärvi puh. +358 3 3488 200 info@DYNASET.com ELECTRICITY MAGNET POWER HG Hydraulic Generator HMG PRO Hydraulic Magnet Generator HGV POWER BOX Variable Hydraulic Generator System MAG Lift Magnet HGV Variable Hydraulic Generator System HMAG PRO Hydraulic Magnet...
Need help?
Do you have a question about the 60 and is the answer not in the manual?
Questions and answers