Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Generac Mobile CTF10
- Page 1 Owner’s Manual CTF10 Light Tower 010128 Register your Generac product at: For technical assistance contact: WWW.GENERAC.COM www.generacmobileproducts.com 1-888-GENERAC Technical Support 1-800-926-9768 (1-888-436-3722) SAVE THIS MANUAL FOR FUTURE REFERENCE...
- Page 2 Use this page to record important information about your Generac Mobile Product Record the information found on your unit data label on this Unit Model Number Serial Number Locations page. See When contacting a Generac Mobile Products Authorized Unit Serial Number Service Dealer (ASD) about parts and service, always supply the complete model number and serial number of the unit.
-
Page 3: Table Of Contents
Programming Timer via Control Panel ......14 Setting the Clock ............14 Section 6: Wiring Diagrams Programming the Timer ..........14 AC Wiring ............25 Internal Storage ............15 Lifting and Transporting ........15 Tying the Unit Down ..........15 Owner’s Manual for CTF10 Light Tower... - Page 4 This page intentionally left blank. Owner’s Manual for CTF10 Light Tower...
-
Page 5: Section 1: Introduction And Safety
Section 1: Introduction and Safety Introduction Safety Rules Thank you for purchasing a Generac Mobile Products LLC The manufacturer cannot anticipate every possible product. This unit has been designed to provide high circumstance that might involve a hazard. The warnings in... -
Page 6: General Hazards
An unsecured unit can suddenly roll or move, causing death or serious injury. (000234a) CAUTION Equipment Damage. Failure to perform a daily inspection could result in damage to the unit. (000306) Owner’s Manual for CTF10 Light Tower... -
Page 7: Operating Safety
WARNING Personal Injury. Stop immediately if the mast hangs up or the winch cable develops slack. Excess slack could cause the mast to collapse, resulting in personal injury or equipment damage. (000265) Owner’s Manual for CTF10 Light Tower... -
Page 8: Safety And Operating Decals
Lifting Point Always: extend the outriggers and level the unit before raising the mast Warning - Pinch Points Maximum Wind Stability Do not Step Tie down point 010186 Figure 1-1. Decal Locations (1 of 5) Owner’s Manual for CTF10 Light Tower... - Page 9 Introduction and Safety 009642 Figure 1-2. Decal Locations (2 of 5) Owner’s Manual for CTF10 Light Tower...
- Page 10 Introduction and Safety 009643 Figure 1-3. Decal Locations (3 of 5) Owner’s Manual for CTF10 Light Tower...
- Page 11 Introduction and Safety 009643 Figure 1-4. Decal Locations (4 of 5) 009644 Figure 1-5. Decal Locations (4 of 4) Owner’s Manual for CTF10 Light Tower...
- Page 12 Introduction and Safety This page intentionally left blank. Owner’s Manual for CTF10 Light Tower...
-
Page 13: Section 2: General Information
(B). Record the information from these tags so it is available if the tags are lost or damaged. When ordering parts or requesting assistance, you may be asked to provide this information. 010191 Figure 2-1. Serial Number Location Owner’s Manual for CTF10 Light Tower... -
Page 14: Unit Dimensions
General Information Unit Dimensions 010192 Figure 2-2. Unit Dimensions CTF-10 100 in (2.54 m) 49.1 in (1.247 m) 32.5 ft (9.9 m) 99.6 in (2.5 m) Specifications are subject to change without notice. Owner’s Manual for CTF10 Light Tower... -
Page 15: Component Locations
Inspection door Extractable stabilizers Floodlights blocking rotation pin Lifting hook Floodlights Safety pin Telescopic mast Floodlights rotation handle Manual winch Inspection door NOTE: For grounding requirements, follow local, state, or National Electrical Code (NEC) guidelines. Owner’s Manual for CTF10 Light Tower... -
Page 16: Control Panel
Light Sensor for more information. • Choose the 20 A setting if auxiliary equipment or a second CTF10 will be connected to the unit. (G) Digital timer Sets timer schedule. Used when Off/Manual/Timer/Light (B) Off/Manual/Timer/Light Sensor Selector Sensor selector is set to Timer. See... -
Page 17: Light Sensor
Sensor LED LED Status Light Sensor Status Off. Ambient lux is greater than Slow blinking threshold setting. On. Ambient lux is less than Steady threshold setting Once installed, follow the on screen programming instructions. Owner’s Manual for CTF10 Light Tower... -
Page 18: Programming Timer Via Control Panel
Selecting ON will turn the unit ON at the Cancel programmed time. Program number • Selecting OFF will turn the unit OFF at the M Program programmed time. Joystick 8. Press joystick for 3 seconds to save the program. Owner’s Manual for CTF10 Light Tower... -
Page 19: Internal Storage
Avoid approaching the unit at an angle, as this can permanently damage the forklift pockets, tires, or cabinet. Verify any obstructions are clear of the forklift tines before lifting. 010129 Figure 2-10. Tying the Unit Down Owner’s Manual for CTF10 Light Tower... - Page 20 General Information This page intentionally left blank. Owner’s Manual for CTF10 Light Tower...
-
Page 21: Section 3: Operation
120VAC-20A supply using the NEMA L5-20 plug. NOTE: Shore power cords are not included with this unit and must be supplied by the end user. See Table 3-1 recommended cable size and length. Owner’s Manual for CTF10 Light Tower... -
Page 22: Prestart Checklist
3-3. Before raising the mast, adjust the receptacle is functional. LED fixtures by loosening handle (E) and aiming the LED in the desired direction. After adjusting, tighten the handle. 010132 Figure 3-3. Adjusting LED Fixture Owner’s Manual for CTF10 Light Tower... -
Page 23: Raising The Mast
STOP extending the mast when the colored mark (C) on the second mast section is visible. IMPORTANT NOTE: Contact a Generac Mobile Prod- ucts Authorized Service Dealer immediately if the mast hangs up or the winch cable develops slack. -
Page 24: Turning Unit On
Figure 3-6. Insert safety pin (G) into mast hole (H) and secure with hairpin (I). IMPORTANT NOTE: Contact a Generac Mobile Prod- ucts Authorized Service Dealer immediately if the mast hangs up or the winch cable develops slack. NOTE: See Control Panel for the location of controls. -
Page 25: Section 4: Maintenance
Cleaning the Unit CAUTION Equipment damage. Never spray water to clean unit. Do not introduce water into generator widings, terminals, or fuel system during the cleaning process. Doing so will result in equipment damage. (000325a) Owner’s Manual for CTF10 Light Tower... -
Page 26: Winch Use, Operation And Maintenance
2. Always be sure the cable is undamaged. Contact Long-Term Storage Generac Mobile Products to order a replacement cable if necessary. Perform the following steps if the machine is to be stored for an extended period. -
Page 27: Section 5: Troubleshooting
Main Breaker Connected load Reduce size of connected load or reduce the number of lights in Switch Trips when (through GFCI) too use. Applying Load large Owner’s Manual for CTF10 Light Tower... - Page 28 Troubleshooting This page intentionally left blank. Owner’s Manual for CTF10 Light Tower...
-
Page 29: Section 6: Wiring Diagrams
Section 6: Wiring Diagrams AC Wiring Owner’s Manual for CTF10 Light Tower... - Page 30 Wiring Diagrams This page intentionally left blank. Owner’s Manual for CTF10 Light Tower...
- Page 32 ©2019 Generac Mobile Products, LLC All rights reserved. Generac Mobile Products, LLC Specifications are subject to change without notice. 215 Power Drive, Berlin, WI 54923 No reproduction allowed in any form without prior written GeneracMobileProducts.com │800-926-9768 │920-361-4442 consent from Generac Mobile Products, LLC.